LM20BIM7X/NOPB National Semiconductor, LM20BIM7X/NOPB Datasheet - Page 4
![IC,TEMPERATURE SENSOR,CMOS,TSSOP,5PIN,PLASTIC](/photos/19/11/191182/4243245_sml.jpg)
LM20BIM7X/NOPB
Manufacturer Part Number
LM20BIM7X/NOPB
Description
IC,TEMPERATURE SENSOR,CMOS,TSSOP,5PIN,PLASTIC
Manufacturer
National Semiconductor
Datasheet
1.LM20C-EVAL.pdf
(10 pages)
Specifications of LM20BIM7X/NOPB
Rohs Compliant
YES
Ic Output Type
Analog
Sensing Accuracy Range
± 2.5°C To ± 5°C
Temperature Sensing Range
-55°C To +130°C
Supply Current
4.5µA
Supply Voltage Range
2.4V To 5.5V
Sensor Case Style
SC-70
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM20BIM7X/NOPB
Manufacturer:
National
Quantity:
22 265
Part Number:
LM20BIM7X/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
www.national.com
Temperature Coefficient of
Quiescent Current
Shutdown Current
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: When the input voltage (V
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged
directly into each pin.
Note 4: Reflow temperature profiles are different for lead-free and non-lead-free packages.
Note 5: The junction to ambient thermal resistance (θ
Note 6: Typicals are at T
Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: Accuracy is defined as the error between the measured and calculated output voltage at the specified conditions of voltage, current, and temperature
(expressed in°C).
Note 9: Non-Linearity is defined as the deviation of the calculated output-voltage-versus-temperature curve from the best-fit straight line, over the temperature
range specified.
Note 10: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be
computed by multiplying the internal dissipation by the thermal resistance.
Note 11: Negative currents are flowing into the LM20. Positive currents are flowing out of the LM20. Using this convention the LM20 can at most sink −1 μA and
source +16 μA.
Note 12: Load regulation or output impedance specifications apply over the supply voltage range of +2.4V to +5.5V.
Note 13: Line regulation is calculated by subtracting the output voltage at the highest supply input voltage from the output voltage at the lowest supply input
voltage.
Typical Performance Characteristics
Parameter
J
= T
A
= 25°C and represent most likely parametric norm.
I
) at any pin exceeds power supplies (V
V
+
≤
+0.8 V
Conditions
JA
) is specified without a heat sink in still air using the printed circuit board layout shown in
Temperature Error vs Temperature
I
< GND or V
4
(Note
Typical
0.02
−11
I
> V
6)
+
), the current at that pin should be limited to 5 mA.
(Note
LM20B
Limits
10090825
7)
(Note
LM20C
Limits
7)
(Note
LM20S
Limits
7)
Figure
(Limit)
nA/°C
Units
μA
1.