LM2575T-15 National Semiconductor, LM2575T-15 Datasheet - Page 21
![Voltage Regulator IC](/photos/18/98/189891/4243351_sml.jpg)
LM2575T-15
Manufacturer Part Number
LM2575T-15
Description
Voltage Regulator IC
Manufacturer
National Semiconductor
Datasheets
1.LM2575T-5.0.pdf
(28 pages)
2.LM2575T-5.0.pdf
(25 pages)
3.LM2575T-5.0.pdf
(25 pages)
4.LM2575T-15.pdf
(10 pages)
Specifications of LM2575T-15
No. Of Pins
5
Output Current
1A
Peak Reflow Compatible (260 C)
No
Output Voltage
15V
Termination Type
Through Hole
Supply Voltage Max
40V
Leaded Process Compatible
No
Mounting Type
Through Hole
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2575T-15
Manufacturer:
ON
Quantity:
500
Company:
Part Number:
LM2575T-15G
Manufacturer:
ON Semiconductor
Quantity:
135
Company:
Part Number:
LM2575T-15G
Manufacturer:
ON Semiconductor
Quantity:
1 100
NEGATIVE BOOST REGULATOR
Another variation on the buck-boost topology is the negative
boost configuration. The circuit in Figure 11 accepts an input
voltage ranging from −5V to −12V and provides a regulated
−12V output. Input voltages greater than −12V will cause the
output to rise above −12V, but will not damage the regulator.
Because of the boosting function of this type of regulator, the
switch current is relatively high, especially at low input volt-
ages. Output load current limitations are a result of the max-
imum current rating of the switch. Also, boost regulators can
not provide current limiting load protection in the event of a
shorted load, so some other means (such as a fuse) may be
necessary.
Typical Load Current
200 mA for V
500 mA for V
Note: Pin numbers are for TO-220 package.
UNDERVOLTAGE LOCKOUT
In some applications it is desirable to keep the regulator off
until the input voltage reaches a certain threshold. An under-
voltage lockout circuit which accomplishes this task is shown
in Figure 12, while Figure 13 shows the same circuit applied
to a buck-boost configuration. These circuits keep the regu-
lator off until the input voltage reaches a predetermined level.
DELAYED STARTUP
The ON /OFF pin can be used to provide a delayed startup
feature as shown in Figure 14. With an input voltage of 20V
and for the part values shown, the circuit provides approxi-
mately 10 ms of delay time before the circuit begins switching.
Increasing the RC time constant can provide longer delay
times. But excessively large RC time constants can cause
problems with input voltages that are high in 60 Hz or 120 Hz
ripple, by coupling the ripple into the ON /OFF pin.
ADJUSTABLE OUTPUT, LOW-RIPPLE
POWER SUPPLY
A 1A power supply that features an adjustable output voltage
is shown in Figure 15. An additional L-C filter that reduces the
output ripple by a factor of 10 or more is included in this circuit.
IN
IN
= −5.2V
= −7V
FIGURE 11. Negative Boost
V
TH
V
Z1
+ 2V
BE
(Q1)
1147516
21
Note: Complete circuit not shown.
Note: Pin numbers are for the TO-220 package.
Note: Complete circuit not shown (see Figure 10).
Note: Pin numbers are for the TO-220 package.
Note: Complete circuit not shown.
Note: Pin numbers are for the TO-220 package.
FIGURE 12. Undervoltage Lockout for Buck Circuit
FIGURE 13. Undervoltage Lockout
FIGURE 14. Delayed Startup
for Buck-Boost Circuit
1147519
www.national.com
1147517
1147518