LM2596S-ADJ National Semiconductor, LM2596S-ADJ Datasheet - Page 14
![DC/DC Converter IC](/photos/19/2/190204/4243352_sml.jpg)
LM2596S-ADJ
Manufacturer Part Number
LM2596S-ADJ
Description
DC/DC Converter IC
Manufacturer
National Semiconductor
Datasheet
1.LM2596S-ADJ.pdf
(31 pages)
Specifications of LM2596S-ADJ
Input Voltage
40V
Output Current
3A
Output Voltage
37V
No. Of Pins
5
Termination Type
SMD
Mounting Type
Through Hole
Voltage Regulator Type
Buck Switching
Output Current Max
3A
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM2596S-ADJ
Manufacturer:
NS
Quantity:
35 306
Company:
Part Number:
LM2596S-ADJ
Manufacturer:
NS
Quantity:
17
Part Number:
LM2596S-ADJ
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
LM2596S-ADJ/NOPB
Manufacturer:
TI
Quantity:
25
Company:
Part Number:
LM2596S-ADJP
Manufacturer:
ADI
Quantity:
30
www.national.com
LM2596 Series Buck Regulator Design Procedure (Adjustable Output)
3. Output Capacitor Selection (C
A. In the majority of applications, low ESR electrolytic or solid
tantalum capacitors between 82 µF and 820 µF provide the
best results. This capacitor should be located close to the IC
using short capacitor leads and short copper traces. Do not
use capacitors larger than 820 µF. For additional informa-
tion, see section on output capacitors in application in-
formation section.
B. To simplify the capacitor selection procedure, refer to the
quick design table shown in Figure 3 . This table contains
different output voltages, and lists various output capacitors
that will provide the best design solutions.
C. The capacitor voltage rating should be at least 1.5 times
greater than the output voltage, and often much higher voltage
ratings are needed to satisfy the low ESR requirements
needed for low output ripple voltage.
4. Feedforward Capacitor (C
For output voltages greater than approximately 10V, an addi-
tional capacitor is required. The compensation capacitor is
typically between 100 pF and 33 nF, and is wired in parallel
with the output voltage setting resistor, R
tional stability for high output voltages, low input-output volt-
ages, and/or very low ESR output capacitors, such as solid
tantalum capacitors.
This capacitor type can be ceramic, plastic, silver mica, etc.
(Because of the unstable characteristics of ceramic capacitors
made with Z5U material, they are not recommended.)
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
FF
) (See Figure 1 )
OUT
)
2
. It provides addi-
14
3. Output Capacitor SeIection (C
A. See section on C
B. From the quick design table shown in Figure 3 , locate the
output voltage column. From that column, locate the output
voltage closest to the output voltage in your application. In this
example, select the 24V line. Under the output capacitor sec-
tion, select a capacitor from the list of through hole electrolytic
or surface mount tantalum types from four different capacitor
manufacturers. It is recommended that both the manufactur-
ers and the manufacturers series that are listed in the table be
used.
In this example, through hole aluminum electrolytic capacitors
from several different manufacturers are available.
C. For a 20V output, a capacitor rating of at least 30V or more
is needed. In this example, either a 35V or 50V capacitor
would work. A 35V rating was chosen, although a 50V rating
could also be used if a lower output ripple voltage is needed.
Other manufacturers or other types of capacitors may also be
used, provided the capacitor specifications (especially the 100
kHz ESR) closely match the types listed in the table. Refer to
the capacitor manufacturers data sheet for this information.
4. Feedforward Capacitor (C
The table shown in Figure 3 contains feed forward capacitor
values for various output voltages. In this example, a 560 pF
capacitor is needed.
220 µF/35V Panasonic HFQ Series
150 µF/35V Nichicon PL Series
EXAMPLE (Adjustable Output Voltage Version)
OUT
in Application Information section.
FF
)
OUT
)