LM2672M-5.0 National Semiconductor, LM2672M-5.0 Datasheet - Page 3

• Manufacturer Part Number: LM2672M-5.0
• Description: DC/DC Converter IC
• Manufacturer: National Semiconductor

Specifications of LM2672M-5.0

• Input Voltage: 40V
• Output Current: 1A
• Output Voltage: 5V
• No. Of Pins: 8
• Mounting Type: Surface Mount
• Voltage Regulator Type: Buck Switching
• Supply Voltage Min: 6.5V
• Output Current Max: 1A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Symbol
Symbol
DEVICE PARAMETERS
I
I
I
I
R
f
D
I
V
I
F
V
V
I
SYSTEM PARAMETERS Test Circuit Figure 3 (Note 3)
Q
STBY
CL
L
O
BIAS
S/D
SS
LM2672-ADJ
Electrical Characteristics
JA
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see
the Electrical Characteristics.
Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k
Note 3: External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator per-
formance. When the LM2672 is used as shown in Figure 2 and Figure 3 test circuits, system performance will be as specified by the system parameters section of
the Electrical Characteristics.
Note 4: Typical numbers are at 25˚C and represent the most likely norm.
Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% pro-
duction tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to cal-
culate Average Outgoing Quality Level (AOQL).
Note 6: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area will
lower thermal resistance further. See Application Information section in the application note accompanying this datasheet and the thermal model in LM267X Made
Simple version 1.0 software.
Specifications with standard type face are for T
Range. Unless otherwise specified, V
and I
SYNC
All Output Voltage Versions
S/D
SYNC
SS
DS(ON)
LOAD
Efficiency
Quiescent Current
Standby Quiescent Current
Current Limit
Output Leakage Current
Switch On-Resistance
Oscillator Frequency
Maximum Duty Cycle
Minimum Duty Cycle
Feedback Bias
Current
ON/OFF Pin
Voltage Thesholds
ON/OFF Pin Current
Synchronization Frequency
Synchronization Threshold
Voltage
Soft-Start Voltage
Soft-Start Current
Thermal Resistance
= 100 mA.
Parameter
Parameters
(Continued)
V
IN
= 12V, I
IN
= 12V for the 3.3V, 5V, and Adjustable versions and V
LOAD
V
For 3.3V, 5.0V, and ADJ Versions
V
For 12V Versions
ON/OFF Pin = 0V
V
V
V
I
Measured at Switch Pin
V
ADJ Version Only
ON/OFF Pin = 0V
V
N Package, Junction to Ambient (Note 6)
M Package, Junction to Ambient (Note 6)
SWITCH
FEEDBACK
FEEDBACK
IN
SWITCH
SWITCH
FEEDBACK
SYNC
Conditions
= 40V, ON/OFF Pin = 0V
J
= 1A
= 25˚C, and those in bold type face apply over full Operating Temperature
= 3.5V, 50% duty cycle
= 1A
= 0V
= −1V, ON/OFF Pin = 0V
= 8V
= 15V
= 1.3V
Conditions
3
resistor into each pin.
(Note 4)
Typ
90
1.55
0.25
0.63
Typ
260
400
105
2.5
2.5
1.4
1.4
4.5
50
95
85
20
95
1
6
0
(Note 5)
IN
Min
1.25/1.2
= 24V for the 12V version,
0.53
Min
225
0.8
1.5
7
(Note 5)
0.30/0.50
100/150
2.1/2.2
Max
Max
0.73
275
3.6
2.0
6.9
25
15
37
www.national.com
Units
Units
˚C/W
kHz
kHz
mA
mA
mA
µA
µA
nA
µA
µA
%
%
%
A
V
V
V