LM5576MH National Semiconductor, LM5576MH Datasheet - Page 10

no-image

LM5576MH

Manufacturer Part Number
LM5576MH
Description
IC,SMPS CONTROLLER,CURRENT-MODE,TSSOP,20PIN,PLASTIC
Manufacturer
National Semiconductor
Datasheets

Specifications of LM5576MH

Rohs Compliant
NO

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM5576MH
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
LM5576MH
Quantity:
35
Part Number:
LM5576MH/NOPB
Manufacturer:
TI
Quantity:
1 600
Part Number:
LM5576MH/NOPB
Manufacturer:
TI
Quantity:
2 845
Part Number:
LM5576MH/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LM5576MHX
Manufacturer:
TI
Quantity:
5 499
Part Number:
LM5576MHX
Manufacturer:
NS/国半
Quantity:
20 000
Part Number:
LM5576MHX
0
Part Number:
LM5576MHX/NOPB
Manufacturer:
TI
Quantity:
1 600
Part Number:
LM5576MHX/NOPB
Manufacturer:
TI
Quantity:
2 845
Part Number:
LM5576MHX/NOPB
Manufacturer:
NSC
Quantity:
8
Part Number:
LM5576MHX/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LM5576MHX/NOPB
0
www.national.com
Shutdown / Standby
The LM5576 contains a dual level Shutdown (SD) circuit.
When the SD pin voltage is below 0.7V, the regulator is in a
low current shutdown mode. When the SD pin voltage is
greater than 0.7V but less than 1.225V, the regulator is in
standby mode. In standby mode the Vcc regulator is active
but the output switch is disabled. When the SD pin voltage
exceeds 1.225V, the output switch is enabled and normal op-
eration begins. An internal 5µA pull-up current source config-
ures the regulator to be fully operational if the SD pin is left
open.
An external set-point voltage divider from VIN to GND can be
used to set the operational input range of the regulator. The
divider must be designed such that the voltage at the SD pin
will be greater than 1.225V when Vin is in the desired oper-
ating range. The internal 5µA pull-up current source must be
included in calculations of the external set-point divider. Hys-
teresis of 0.1V is included for both the shutdown and standby
thresholds. The SD pin is internally clamped with a 1kΩ re-
sistor and an 8V zener clamp. The voltage at the SD pin
should never exceed 14V. If the voltage at the SD pin exceeds
8V, the bias current will increase at a rate of 1 mA/V.
The SD pin can also be used to implement various remote
enable / disable functions. Pulling the SD pin below the 0.7V
threshold totally disables the controller. If the SD pin voltage
is above 1.225V the regulator will be operational.
Oscillator and Sync Capability
The LM5576 oscillator frequency is set by a single external
resistor connected between the RT pin and the AGND pin.
The R
connected directly to the pins of the IC (RT and AGND).To
set a desired oscillator frequency (F), the necessary value for
the R
The SYNC pin can be used to synchronize the internal oscil-
lator to an external clock. The external clock must be of
higher frequency than the free-running frequency set by the
R
recommended interface from the external clock to the SYNC
pin. The clock pulse duration should be greater than 15ns.
T
resistor. A clock circuit with an open drain output is the
T
T
resistor can be calculated from the following equation:
resistor should be located very close to the device and
FIGURE 3. Sync from External Clock
20189905
10
Multiple LM5576 devices can be synchronized together sim-
ply by connecting the SYNC pins together. In this configura-
tion all of the devices will be synchronized to the highest
frequency device. The diagram in Figure 5 illustrates the
SYNC input/output features of the LM5576. The internal os-
cillator circuit drives the SYNC pin with a strong pull-down /
weak pull-up inverter. When the SYNC pin is pulled low either
by the internal oscillator or an external clock, the ramp cycle
of the oscillator is terminated and a new oscillator cycle be-
gins. Thus, if the SYNC pins of several LM5576 IC’s are
connected together, the IC with the highest internal clock fre-
quency will pull the connected SYNC pins low first and termi-
nate the oscillator ramp cycles of the other IC’s. The LM5576
with the highest programmed clock frequency will serve as
the master and control the switching frequency of the all the
devices with lower oscillator frequency.
FIGURE 4. Sync from Multiple Devices
20189906

Related parts for LM5576MH