LM75BIM-3 National Semiconductor, LM75BIM-3 Datasheet - Page 5

• Manufacturer Part Number: LM75BIM-3
• Description: Temperature Sensor IC
• Manufacturer: National Semiconductor

Specifications of LM75BIM-3

• Peak Reflow Compatible (260 C): No
• Ic Function: Temperature Sensor IC
• Supply Voltage Max: 5.5V
• Leaded Process Compatible: No
• Supply Voltage Min: 3V
• Operating Temperature Min: -55°C
• Package / Case: 8-SOIC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

t
t
t
t
t
t
1
2
3
4
5
TIMEOUT
Symbol
Logic Electrical Characteristics
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its rated operating conditions.
Note 2: When the input voltage (V
maximum package input current rating limits the number of pins that can safely exceedthe power supplies with an input current of 5 mA to four.
Note 3: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National
Semiconductor Linear Data Book for other methods of soldering surface mount devices.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin.
I
LM75BIM-5, LM75BIMM-5, LM75CIM-5, and LM75CIMM-5 and +V
and LM75CIMM-3. C
T
meet or exceed the published specifications of the I
and SDA signals related to the LM75. They are not the I
Symbol
2
DIGITAL DC CHARACTERISTICS Unless otherwise noted, these specifications apply for +V
LM75BIMM-5, LM75CIM-5, and LM75CIMM-5 and +V
LM75CIMM-3 (Note 6). Boldface limits apply for T
noted.
J
C DIGITAL SWITCHING CHARACTERISTICS Unless otherwise noted, these specifications apply for +V
= T
MIN
SCL (Clock) Period
Data in Set-Up Time to SCL High
Data Out Stable after SCL Low
SDA Low Set-Up Time to SCL Low (Start Condition)
SDA High Hold Time after SCL High (Stop Condition)
SDA Time Low for Reset of Serial Interface (Note 13)
to T
MAX
; all other limits T
L
(load capacitance) on output lines = 80 pF unless otherwise specified. Boldface limits apply for T
Parameter
I
) at any pin exceeds the power supplies (V
A
Parameter
= T
J
= +25˚C, unless otherwise noted. The switching characteristics of the LM75 fully
I
O
Conditions
= 3 mA
2
C bus. The following parameters are the timing relationships between SCL
A
(Continued)
S
= T
= +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3, and
2
C bus specifications.
J
= T
I
<
5
MIN
GND or V
LM75B
LM75C
S
to T
= +3.3 Vdc for LM75BIM-3, LM75BIMM-3, LM75CIM-3,
I
MAX
>
(Note 12)
Typical
+V
; all other limits T
S
Conditions
) the current at that pin should be limited to 5 mA. The 20 mA
(Note 12)
Typical
A
S
(Note 7)
Limits
= T
= +5 Vdc for LM75BIM-5,
J
01265804
= +25˚C, unless otherwise
Applicable
(Note 7)
Limits
S
100
100
100
325
Not
2.5
75
= +5 Vdc for
0
www.national.com
(Limit)
Units
ms (max)
ms (min)
µs (min)
ns (min)
ns (min)
ns (min)
ns (min)
(Limit)
Units
A
=