LP2987IMM-5.0 National Semiconductor, LP2987IMM-5.0 Datasheet - Page 15
![Linear Voltage Regulator IC](/photos/18/97/189768/3778330_sml.jpg)
LP2987IMM-5.0
Manufacturer Part Number
LP2987IMM-5.0
Description
Linear Voltage Regulator IC
Manufacturer
National Semiconductor
Specifications of LP2987IMM-5.0
No. Of Pins
8
Output Current
0.2A
Mounting Type
Surface Mount
Voltage Regulator Type
LDO Linear
Output Current Max
250mA
Peak Reflow Compatible (260 C)
No
Output Voltage
5V
Current Rating
0.2A
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP2987IMM-5.0
Manufacturer:
NSC
Quantity:
2 500
Company:
Part Number:
LP2987IMM-5.0
Manufacturer:
NS
Quantity:
1 000
Company:
Part Number:
LP2987IMM-5.0
Manufacturer:
NSC
Quantity:
1 000
Application Hints
EXTERNAL CAPACITORS
As with any low-dropout regulator, external capacitors are
required to assure stability. These capacitors must be cor-
rectly selected for proper performance.
INPUT CAPACITOR: An input capacitor ( 2.2 µF) is re-
quired between the LP2987/8 input and ground (amount of
capacitance may be increased without limit).
This capacitor must be located a distance of not more than
0.5” from the input pin and returned to a clean analog
ground. Any good quality ceramic or tantalum may be used
for this capacitor.
OUTPUT CAPACITOR: The output capacitor must meet the
requirement for minimum amount of capacitance and also
have an appropriate E.S.R. (equivalent series resistance)
value.
Curves are provided which show the allowable ESR range
as a function of load current for 3V and 5V outputs.
IMPORTANT: The output capacitor must maintain its ESR in
the stable region over the full operating temperature range of
the application to assure stability.
The minimum required amount of output capacitance is
4.7 µF. Output capacitor size can be increased without limit.
It is important to remember that capacitor tolerance and
variation with temperature must be taken into consideration
when selecting an output capacitor so that the minimum re-
ESR Curves For 5V Output
ESR Curves For 3V Output
DS100017-7
DS100017-8
15
quired amount of output capacitance is provided over the full
operating temperature range. A good Tantalum capacitor will
show very little variation with temperature, but a ceramic
may not be as good (see next section).
The output capacitor should be located not more than 0.5”
from the output pin and returned to a clean analog ground.
CAPACITOR CHARACTERISTICS
TANTALUM: A solid tantalum capacitor is the best choice for
the output capacitor on the LM2987/8. Available from many
sources, their typical ESR is very close to the ideal value re-
quired on the output of many LDO regulators.
Tantalums also have good temperature stability: a 4.7 µF
was tested and showed only a 10% decline in capacitance
as the temperature was decreased from +125˚C to −40˚C.
The ESR increased only about 2:1 over the same range of
temperature.
However, it should be noted that the increasing ESR at lower
temperatures present in all tantalums can cause oscillations
when marginal quality capacitors are used (where the ESR
of the capacitor is near the upper limit of the stability range at
room temperature).
CERAMIC: The ESR of ceramic capacitor can be low
enough to cause an LDO regulator to oscillate: a 2.2 µF ce-
ramic was measured and found to have an ESR of 15 m .
If a ceramic capacitor is to be used on the LP2987/8 output,
a 1 resistor should be placed in series with the capacitor to
provide a minimum ESR for the regulator.
A disadvantage of ceramic capacitors is that their capaci-
tance varies a lot with temperature: Large ceramic capaci-
tors are typically manufactured with the Z5U temperature
characteristic, which results in the capacitance dropping by
50% as the temperature goes from 25˚C to 80˚C.
This means you have to buy a capacitor with twice the mini-
mum C
ALUMINUM: The large physical size of aluminum electrolyt-
ics makes them unsuitable for most applications. Their ESR
characteristics are also not well suited to the requirements of
LDO regulators. The ESR of a typical aluminum electrolytic
is higher than a tantalum, and it also varies greatly with tem-
perature.
A typical aluminum electrolytic can exhibit an ESR increase
of 50X when going from 20˚C to −40˚C. Also, some alumi-
num electrolytics can not be used below −25˚C because the
electrolyte will freeze.
POWER-ON RESET DELAY
A power-on reset function can be easily implemented using
the LP2987/8 by adding a single external capacitor to the
Delay pin. The Error output provides the power-on reset sig-
nal when input power is applied to the regulator.
The reset signal stays low for a pre-set time period after
power is applied to the regulator, and then goes high (see
Timing Diagram below).
OUT
to assure stable operation up to 80˚C.
www.national.com