MCP73833-NVI/UN Microchip Technology, MCP73833-NVI/UN Datasheet - Page 14
![1A Li-Ion/Li-Poly Charge Mgmt Controller, PG Output 10 MSOP 3x3mm TUBE](/photos/6/59/65940/c04-021-msop_sml.jpg)
MCP73833-NVI/UN
Manufacturer Part Number
MCP73833-NVI/UN
Description
1A Li-Ion/Li-Poly Charge Mgmt Controller, PG Output 10 MSOP 3x3mm TUBE
Manufacturer
Microchip Technology
Specifications of MCP73833-NVI/UN
Function
Charge Management
Battery Type
Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
Voltage - Supply
3.75 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-TFSOP (0.118", 3.00mm Width)
Output Voltage
4.2 V, 4.35 V, 4.4 V, 4.5 V
Output Current
1200 mA
Operating Supply Voltage
3.75 V to 6 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MCP73833EV - BOARD EVAL FOR MCP73833
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
MCP73833/4
4.1
An internal under voltage lockout (UVLO) circuit
monitors the input voltage and keeps the charger in
shutdown mode until the input supply rises above the
UVLO threshold. The UVLO circuitry has a built-in
hysteresis of 100 mV.
In the event a battery is present when the input power
is applied, the input supply must rise +150 mV above
the battery voltage before the MCP73833/4 becomes
operational.
The UVLO circuit places the device in shutdown mode
if the input supply falls to within +50 mV of the battery
voltage.
The UVLO circuit is always active. At any time the input
supply is below the UVLO threshold or within +50 mV
of the voltage at the V
placed in a shutdown mode.
During any UVLO condition, the battery reverse
discharge current shall be less than 2 µA.
4.2
For a charge cycle to begin, all UVLO conditions must
be met and a battery or output load must be present.
A charge current programming resistor must be
connected from PROG to V
or floating, the MCP73833/4 is disabled and the battery
reverse discharge current is less than 2 µA. In this
manner, the PROG pin acts as a charge enable and
can be used as a manual shutdown.
If the input supply voltage is above the UVLO
threshold,
MCP73833/4 will pulse the STAT1 and PG outputs as
the device determines if a battery is present.
4.3
If the voltage at the V
preconditioning threshold, the MCP73833/4 enters a
preconditioning
preconditioning threshold is factory set. Refer to
Section 1.0
preconditioning threshold options.
In this mode, the MCP73833/4 supplies a percentage
of the charge current (established with the value of the
resistor connected to the PROG pin) to the battery. The
percentage or ratio of the current is factory set. Refer to
Section 1.0
preconditioning current options.
When the voltage at the V
conditioning threshold, the MCP73833/4 enters the
constant current or fast charge mode.
DS22005B-page 14
Under Voltage Lockout (UVLO)
Charge Qualification
Preconditioning
but
“Electrical
“Electrical
or
below
trickle
BAT
BAT
BAT
SS
V
pin, the MCP73833/4 is
REG
. If the PROG pin is open
pin rises above the pre-
Characteristics”
Characteristics”
pin is less than the
charge
(Typical)+0.3V,
mode.
The
the
for
for
4.4
During the constant current mode, the programmed
charge current is supplied to the battery or load. The
charge current is established using a single resistor
from PROG to V
charge current are calculated using
EQUATION 4-1:
Constant current mode is maintained until the voltage
at the V
When constant current mode is invoked, the internal
timer is reset.
4.4.1
If the internal timer expires before the recharge voltage
threshold is reached, a timer fault is indicated and the
charge cycle terminates. The MCP73833/4 remains in
this condition until the battery is removed, the input
power is removed, or the PROG pin is opened. If the
battery is removed or the PROG pin is opened, the
MCP73833/4 enters the Standby mode where it
remains until a battery is reinserted or the PROG pin is
reconnected. If the input power is removed, the
MCP73833/4 is in Shutdown. When the input power is
reapplied, a normal start-up sequence ensues.
4.5
When the voltage at the V
regulation voltage, V
begins. The regulation voltage is factory set to 4.20V,
4.35V, 4.40V, or 4.50V with a tolerance of ± 0.75%.
4.6
The charge cycle is terminated when, during constant
voltage mode, the average charge current diminishes
below a percentage of the programmed charge current
(established with the value of the resistor connected to
the PROG pin) or the internal timer has expired. A 1 ms
filter time on the termination comparator ensures that
transient load conditions do not result in premature
charge cycle termination. The percentage or ratio of the
current is factory set. The timer period is factory set
and can be disabled. Refer to Section 1.0 “Electrical
Characteristics” for charge termination current ratio
and timer period options.
The charge current is latched off and the MCP73833/4
enters a charge complete mode.
Where:
R
PROG
I
REG
BAT
Constant Current - Fast Charge
Mode
Constant Voltage Mode
Charge Termination
pin reaches the regulation voltage, V
TIMER EXPIRED DURING
CONSTANT CURRENT - FAST
CHARGE MODE
= kilo-ohms
= milliampere
SS
I
REG
. The program resistor and the
REG
© 2009 Microchip Technology Inc.
, constant voltage regulation
=
---------------- -
R
1000V
PROG
BAT
Equation
pin reaches the
4-1:
REG
.