PIC16F628AT-I/SS Microchip Technology, PIC16F628AT-I/SS Datasheet - Page 6
![IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,20PIN,PLASTIC](/photos/6/58/65895/150-20-ssop_sml.jpg)
PIC16F628AT-I/SS
Manufacturer Part Number
PIC16F628AT-I/SS
Description
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,20PIN,PLASTIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Specifications of PIC16F628AT-I/SS
Rohs Compliant
YES
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
224 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
I3DBF648 - BOARD DAUGHTER ICEPIC3AC162053 - HEADER INTERFACE ICD,ICD2 18DIP
Data Converters
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIC16F627A/628A/648A
The optional 16-bit data word will either be an input to,
or an output from the PIC
on the command. Load Data commands will be input,
and Read Data commands will be output. The 16-bit
data word only contains 14 bits of data to conform to the
14-bit program memory word. The 14 bits are centered
within the 16-bit word, padded with a leading and trail-
ing zero.
Program/Verify mode may be entered via one of two
methods. High voltage Program/Verify is entered by
holding CLOCK and DATA pins low while raising MCLR
first, then V
Program/Verify mode is entered by raising V
MCLR and PGM, as shown in Figure 2-3. The PC will
be set to ‘0’ upon entering into Program/Verify mode.
The PC can be changed by the execution of either an
increment PC command, or a Load Configuration
command, which sets the PC to 0x2000.
All other logic is held in the Reset state while in
Program/Verify mode. This means that all I/O are in the
Reset state (high-impedance inputs).
If LVP is not being used for programming and the LVP
Configuration bit is set (i.e., LVP feature is enabled),
the PGM pin must not be allowed to toggle while
programming. The PGM pin is edge sensitive and if an
edge is detected during programming, it may cause the
PC to reset. If the LVP feature is disabled, the PGM pin
will have no effect on programming.
FIGURE 2-2:
DS41196G-page 6
Note:
CLOCK
Note:
MCLR
DATA
V
LVP
DD
The LVP feature is enabled by default
when the LVP bit of the Configuration
Word is set.
DD
If the LVP fuse is enabled, PGM should be
held low to prevent inadvertent entry into LVP
mode.
as shown in Figure 2-2. Low voltage
Tppdp
ENTERING HIGH
VOLTAGE PROGRAM/
VERIFY MODE
®
microcontroller, depending
Thld0
DD
, then
Preliminary
FIGURE 2-3:
CLOCK
Note:
MCLR
DATA
PGM
V
DD
If the device is in LVP mode, raising V
V
IHH
will override LVP mode.
Thld0
ENTERING LOW
VOLTAGE PROGRAM/
VERIFY MODE
© 2007 Microchip Technology Inc.
Tlvpp
Tppdp
PP
to