PIC16F630-E/SL Microchip Technology, PIC16F630-E/SL Datasheet - Page 7

• Manufacturer Part Number: PIC16F630-E/SL
• Description: 14 PIN, 1.75KB STD FLASH, 64 RAM, 12 I/O,
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F630-E/SL

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 12
• Program Memory Size: 1.75KB (1K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.3.1.3
After receiving this command, the chip will load in a
14-bit data word when 16 cycles are applied. However,
the data memory is only 8 bits wide and thus, only the
first 8 bits of data after the Start bit will be programmed
into the data memory. It is still necessary to cycle the
clock the full 16 cycles in order to allow the internal
circuitry to reset properly. The data memory contains
128 bytes. Only the lower 8 bits of the PC are decoded
by the data memory and therefore, if the PC is greater
than 0x7F, it will wrap around and address a location
within the physically implemented memory.
FIGURE 2-5:
2.3.1.4
After receiving this command, the chip will transmit
data bits out of the program memory (user or
configuration) currently accessed, starting with the
second rising edge of the clock input. The data pin will
go into Output mode on the second rising clock edge
and revert to Input mode (high-impedance) after the
16th rising edge.
FIGURE 2-6:
© 2005 Microchip Technology Inc.
CLOCK
CLOCK
GP0
GP0
GP1
GP1
DATA
DATA
Note 1: GP0 and GP1 apply to PIC12F629/675 only. For PIC16F630/676, use RA0 and RA1, respectively.
Note 1: GP0 and GP1 apply to PIC12F629/675 only. For PIC16F630/676, use RA0 and RA1, respectively.
(1)
(1)
(1)
(1)
Load Data For Data Memory
Read Data From Program Memory
1
1
1
0
T
LOAD DATA FOR DATA MEMORY COMMAND
READ DATA FROM PROGRAM MEMORY COMMAND
SET
2
2
1
0
1
3
3
0
1
Input
Input
T
HLD
4
4
0
PIC12F629/675/PIC16F630/676
0
1
5
5
x
x
x
x
6
6
T
T
T
T
DLY
DLY
DLY
DLY
2
2
1
1
strt_bit
strt_bit
1
1
If the program memory is code-protected (CP = 0), the
data is read as zeros.
2
2
LSb
LSb
T
T
DLY
DLY
3
3
3
3
4
4
Output
Output
5
5
15
15
DS41191D-page 7
MSb
MSb
16
16
Input
Input
stp_bit
stp_bit