PIC16F630-E/ST Microchip Technology, PIC16F630-E/ST Datasheet - Page 67
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC16F630-E/ST
Manufacturer Part Number
PIC16F630-E/ST
Description
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TSSOP,14PIN,PLASTIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC12F629T-ISN.pdf
(24 pages)
3.PIC16F630-ISL.pdf
(132 pages)
4.PIC16F630-ISL.pdf
(2 pages)
5.PIC16F630-ISL.pdf
(10 pages)
Specifications of PIC16F630-E/ST
Rohs Compliant
YES
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
12
Program Memory Size
1.75KB (1K x 14)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
14-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
9.4.1
External interrupt on RA2/INT pin is edge-triggered;
either rising if INTEDG bit (OPTION<6>) is set, or
falling, if INTEDG bit is clear. When a valid edge
appears
(INTCON<1>) is set. This interrupt can be disabled by
clearing the INTE control bit (INTCON<4>). The INTF
bit must be cleared in software in the Interrupt Service
Routine before re-enabling this interrupt. The RA2/INT
interrupt can wake-up the processor from Sleep if the
INTE bit was set prior to going into Sleep. The status of
the GIE bit decides whether or not the processor
branches to the interrupt vector following wake-up. See
Section 9.7 “Power-Down Mode (Sleep)” for details
on Sleep and Figure 9-13 for timing of wake-up from
Sleep through RA2/INT interrupt.
9.4.2
An overflow (FFh 00h) in the TMR0 register will
set the T0IF (INTCON<2>) bit. The interrupt can
be
(INTCON<5>) bit. For operation of the Timer0 module,
see Section 4.0 “Timer0 Module”.
FIGURE 9-11:
2010 Microchip Technology Inc.
INSTRUCTION FLOW
Note:
Note 1: INTF flag is sampled here (every Q1).
GIE bit
(INTCON<7>)
INTF Flag
(INTCON<1>)
CLKOUT
INT pin
OSC1
Instruction
Executed
Instruction
Fetched
PC
enabled/disabled
2: Asynchronous interrupt latency = 3-4 T
3: CLKOUT is available only in RC Oscillator mode.
4: For minimum width of INT pulse, refer to AC specs.
5: INTF is enabled to be set any time during the Q4-Q1 cycles.
on
The ANSEL (91h) and CMCON (19h)
registers must be initialized to configure an
analog channel as a digital input. Pins
configured as analog inputs will read ‘0’.
The ANSEL register is defined for the
PIC16F676.
RA2/INT INTERRUPT
TMR0 INTERRUPT
is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3
the
Q1
Inst (PC - 1)
RA2/INT
Inst (PC)
INT PIN INTERRUPT TIMING
1
Q2
PC
by
Q3
4
setting/clearing
pin,
Q4
5
Q1
the
Inst (PC + 1)
Inst (PC)
Q2
1
INTF
PC + 1
CY
Q3
. Synchronous latency = 3 T
T0IE
bit
Q4
Interrupt Latency
Q1
Dummy Cycle
Q2
9.4.3
An input change on PORTA change sets the RAIF
(INTCON<0>) bit. The interrupt can be enabled/
disabled by setting/clearing the RAIE (INTCON<3>)
bit. Plus individual pins can be configured through the
IOCA register.
9.4.4
See
description of comparator interrupt.
9.4.5
After a conversion is complete, the ADIF flag (PIR<6>)
is set. The interrupt can be enabled/disabled by setting
or clearing ADIE (PIE<6>).
See Section 7.0 “Analog-to-Digital Converter (A/D)
Module (PIC16F676 only)” for operation of the A/D
converter interrupt.
PC + 1
—
Note:
Q3
Section 6.9
Q4
CY
2
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RAIF inter-
rupt flag may not get set.
, where T
PORTA INTERRUPT
COMPARATOR INTERRUPT
A/D CONVERTER INTERRUPT
Q1
Dummy Cycle
PIC16F630/676
Inst (0004h)
Q2
CY
0004h
“Comparator
= instruction cycle time. Latency
Q3
Q4
Q1
DS40039F-page 67
Interrupts”
Inst (0005h)
Q2
Inst (0004h)
0005h
Q3
Q4
for