PIC16LF627-04I/SO Microchip Technology, PIC16LF627-04I/SO Datasheet - Page 108
![IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,18PIN,PLASTIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16LF627-04I/SO
Manufacturer Part Number
PIC16LF627-04I/SO
Description
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,18PIN,PLASTIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheet
1.PIC16F627-04P.pdf
(170 pages)
Specifications of PIC16LF627-04I/SO
Rohs Compliant
YES
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Connectivity
UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Size
1.75KB (1K x 14)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
224 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
18-SOIC (7.5mm Width)
Processor Series
PIC16LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
224 B
Interface Type
SCI, USART
Maximum Clock Frequency
4 MHz
Number Of Programmable I/os
16
Number Of Timers
8
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16LF627-04I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC16F62X
14.12 In-Circuit Serial Programming
The PIC16F62X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware, or a custom
firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After RESET, to place the device into Programming/
Verify mode, the program counter (PC) is at location
00h. A 6-bit command is then supplied to the device.
Depending on the command, 14 bits of program data
are then supplied to or from the device, depending if
the command was a load or a read. For complete
details of serial programming, please refer to the
Programming Specifications.
A typical in-circuit serial programming connection is
shown in Figure 14-18.
FIGURE 14-18:
DS40300C-page 106
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
PP
) pin from V
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
IL
to V
IHH
(see programming
V
V
RA5/MCLR/V
RB6/PGC
RB7/PGD
V
PIC16F62X
DD
DD
SS
PP
Preliminary
14.13 Low Voltage Programming
The LVP bit of the configuration word, enables the low
voltage programming. This mode allows the microcon-
troller to be programmed via ICSP using only a 5V
source. This mode removes the requirement of V
be placed on the MCLR pin. The LVP bit is normally
erased to '1', which enables the low voltage program-
ming. In this mode, the RB4/PGM pin is dedicated to
the programming function and ceases to be a general
purpose I/O pin. The device will enter Programming
mode when a '1' is placed on the RB4/PGM pin. The
HV Programming mode is still available by placing V
on the MCLR pin.
If Low voltage Programming mode is not used, the LVP
bit can be programmed to a '0', and RB4/PGM
becomes a digital I/O pin. To program the device, V
must be placed onto MCLR during programming. The
LVP bit may only be programmed when programming
is entered with V
programmed when programming is entered with RB4/
PGM.
It should be noted, that once the LVP bit is programmed
to 0, High voltage Programming mode can be used to
program the device.
Note 1: While in this mode, the RB4 pin can no
2: V
longer be used as a general purpose I/O
pin.
program operations while in low voltage
Programming mode.
DD
IHH
must be 5.0V +10% during erase/
on MCLR. The LVP bit cannot be
2003 Microchip Technology Inc.
IHH
IHH
IHH
to