ALE14B12 PANASONIC EW, ALE14B12 Datasheet - Page 4

• Manufacturer Part Number: ALE14B12
• Description: RELAY, PCB/TAB, SPNO, 12VDC
• Manufacturer: PANASONIC EW

Specifications of ALE14B12

• Relay Type: Power
• Coil Voltage Vdc Nom: 12V
• Contact Current Max: 16A
• Contact Voltage Ac Nom: 277V
• Coil Resistance: 360ohm
• Coil Type: DC Coil
• Coil Current: 33.3mA
• Nom Operating Power: 400mW
• Relay: RoHS Compliant
• Contact Configuration: SPNO
• Rohs Compliant: Yes

NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be rectangu-
lar. If it includes ripple, the ripple factor
should be less than 5%. However, check
it with the actual circuit since the charac-
teristics may be slightly different.
2. Voltage applied to coil
To ensure reliable operation, please ap-
ply nominal voltage to the coil. Beware of
the fact that pick-up voltage and dropout
voltage vary depending on the ambient
temperature and conditions.
3. Cleaning
This relay is not the sealed type, so it
cannot be immersion cleaned. Be careful
that flux does not overflow onto the PC
board or penetrate inside the relay.
4. Operating life
Operating life varies depending on the
type and load of the coil drive circuit, as
well as factors like the operating frequen-
cy, operating phase and ambient atmo-
sphere, so please check with actual
equipment.
5. Soldering
We recommend the following soldering
conditions.
1) Automatic soldering
* Preheating: 100 C
(PC board solder surface)
Please contact ..........
ASCT1B213E OCT.99 3YT
212
°
F, within 2 mins
* Soldering: 260 C
2) Hand soldering
* Iron tip temperature: 280 to 300 C
to 572
* Soldering iron: 30 to 60W
* Soldering time: Within 5 s
6. Usage, transport and storage
conditions
1) Ambient temperature, humidity, and at-
mospheric pressure during usage, trans-
port, and storage of the relay:
(1) Temperature:
–40 to +85 F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the tem-
perature. Use within the range indicated
in the graph below.
(Avoid freezing when
used at temperatures
lower than 0˚C 32˚F)
Specifications are subject to change without notice.
°
F
–40
–40
Tolerance range
These materials are printed on 100% recycled paper.
These materials are printed with earth-friendly vegetable-based (soybean oil) ink.
–40 to +185
85
5
+32
0
(Avoid
condensation when
used at temperatures
higher than 0˚C 32˚F)
Humidity, %RH
Temperature, ˚C
500
°
F, within 5 s
°
F
˚F
Matsushita Electric Works, Ltd.
Automation Controls Company
K Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan
K Telephone: Japan (81) Osaka [phone]
K Facsimile: Japan (81) Osaka [phone]
http://www.mew.co.jp/e-acg/
+185
+85
536
(3) Atmospheric pressure: 86 to 106 kPa
2) Condensation
Condensation forms when there is a sud-
den change in temperature under high
temperature and high humidity condi-
tions. Condensation will cause deteriora-
tion of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the tempera-
tures is lower than 0 C
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity envi-
ronments
The plastic becomes brittle if the relay is
exposed to a low temperature, low hu-
midity environment for long periods of
time.
7. Others
1) If in error the relay has been dropped,
the appearance and characteristics
should be checked before use without
fail.
2) Please do not use the coating material
of organic system which contains sol-
vents such as xylene and toluene for this
product.
COPYRIGHT © 1999 All Rights Reserved
32
°
F. This causes
Printed in Japan.