G6L-1P 3DC Omron, G6L-1P 3DC Datasheet - Page 8
![RELAY, PCB, SPNO, 3VDC](/photos/19/26/192600/42269572_sml.jpg)
G6L-1P 3DC
Manufacturer Part Number
G6L-1P 3DC
Description
RELAY, PCB, SPNO, 3VDC
Manufacturer
Omron
Datasheet
1.G6L-1F_24DC.pdf
(8 pages)
Specifications of G6L-1P 3DC
Contact Current Max
1A
Contact Voltage Ac Nom
125V
Contact Voltage Dc Nom
24V
Coil Voltage Vdc Nom
3V
Coil Resistance
50ohm
Relay Mounting
PC Board
Coil Type
DC Coil, Monostable
Coil Current
60mA
Contact Configuration
SPNO
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
G6L
Precautions
For general precautions, refer to the PCB Relay Catalog (X033).
Familiarize yourself with the precautions and glossary before
using the G6L.
Correct Use
Handling
Leave the Relays packed until just prior to mounting them.
Soldering
Solder: JIS Z3282, H63A
Soldering temperature: Approx. 250ºC (At 260ºC if the DWS
method is used.)
Soldering time: Approx. 5 s max. (approx. 2 s for the first time and
approx. 3 s for the second time if the DWS method is used.)
Be sure to adjust the level of the molten solder so that the solder
will not overflow onto the PCB.
Claw Securing Force During Automatic Insertion
During automatic insertion of Relays, make sure to set the
securing force of the claws to the following values so that the
Relay characteristics will be maintained.
Environmental Conditions During Operation, Storage, and
Transportation
Protect the Relays from direct sunlight and keep the Relays under
normal temperature, humidity, and pressure.
OMRON Corporation
Electronics Components Company
Electronic & Mechanical Components Division H.Q.
Low Signal Relay Division
2-1, 2-Chome, Nishikusatsu, Kusatsu-City,
Shiga, 525-0035 Japan
Tel: (81)77-565-5841/Fax: (81)77-565-5581
Cat. No. K119-E1-01
Secure the claws to the area indicated by shading.
Do not attach them to the center area or to only part of the
Relay.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
A
Direction A: 5.0 N max.
Direction B: 5.0 N max.
Direction C: 5.0 N max.
In the interest of product improvement, specifications are subject to change without notice.
C
B
Maximum Voltage
The maximum voltage of the coil can be obtained from the coil
temperature increase and the heat-resisting temperature of coil
insulating
temperature may result in burning or short-circuiting.)
maximum voltage also involves important restrictions which
include the following:
• Must not cause thermal changes in or deterioration of the
• Must not cause damage to other control devices.
• Must not cause any harmful effect on people.
• Must not cause fire.
Therefore, be sure not to exceed the maximum voltage specified
in the catalog.
As a rule, the rated voltage must be applied to the coil. A voltage
exceeding the rated value, however, can be applied to the coil
provided that the voltage is less than the maximum voltage. It
must be noted that continuous voltage application to the coil will
cause a coil temperature increase thus affecting characteristics
such as electrical life and resulting in the deterioration of coil
insulation.
Coating
Relays mounted on PCBs may be coated or washed. Do not
apply silicone coating or detergent containing silicone, otherwise
the silicone coating or detergent may remain on the surface of the
Relays.
insulating material.
sheath
material.
(Exceeding
Printed in Japan
0302-2M (0701) (B)
the
heat-resisting
G6L
The