LSTD1R IDEC, LSTD1R Datasheet - Page 7

• Manufacturer Part Number: LSTD1R
• Description: SWITCH COMPONENT
• Manufacturer: IDEC

Specifications of LSTD1R

• For Use With: AP6S Series Miniature Pilot Lights
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

•
•
•
•
1. Make sure that the voltage rating and terminal style of the AP
. Install the pilot light into a panel cut-out before mounting an AC
3. When installing an AC adapter, DC-DC converter, or flasher unit,
4. To remove the AC adapter or DC-DC converter, or flasher unit,
5. When using an AC adapter or DC-DC converter, or flasher
10
ø8·10·1·16
X2 Negative Terminal
Turn off power to the AP series pilot lights before installation, re-
moval, wiring, maintenance, and inspection. Failure to turn power
off may cause electrical shocks or fire hazard.
For wiring, use wires of proper size to meet the voltage and cur-
rent requirements. Improper wiring may cause overheating and
Panel Mounting
Installing the AC Adapter, DC-DC Converter, and
Flasher Unit
When mounting the AP series pilot lights on a panel, use the
optional locking ring wrench. Do not use pliers. Excessive
tightening will damage the locking ring.
series pilot lights are applicable to the AC adapter, DC-DC
converter, and flasher units.
adapter, DC-DC converter, or flasher unit. Note that the pilot light
cannot be installed in a panel cut-out with an AC adapter, DC-
DC converter, or flasher unit mounted.
make sure that the TOP marking is on the same side as the
TOP making of the pilot light. AC adapter, DC-DC converter, and
flasher unit are snapped on to the back of the pilot light.
insert the tip of the removal tool into the joint hook and pull
towards you as shown in the photo below.
unit where the units are subjected to noise, connect a noise
supressor across terminals X1 and X as shown in the diagram
below.
AP6M
APM
AP1M
AP8M
Safety Precautions
Instructions
Unit
X2 Negative Terminal
Nameplate
X1 Positive Terminal
Tightening Torque
0.88 N·m
0.78 N·m
0.9 N·m
0.9 N·m
Positive Terminal
X1 Positive Terminal
TOP
Note: Do not apply excessive force to
AP
TOP
Negative Terminal
Positive Terminal
Noise Suppressor
terminals X1 and X2 during wiring.
Nameplate
Series
X1
X2
TOP
Negative Terminal
AP2 Series
Miniature Pilot Lights
TOP
AP6 Series
•
1. Note the positive and negative polarities when wiring.
. All DC type AP series pilot lights contain a diode for protection
3. Solder the terminal at 350°C within 3 seconds using a 60W
•
•
•
create a fire hazard. Tighten the M3 terminal screws to a torque
of 0.6 to 1.0 N·m. Failure to tighten terminal screws may cause
overheating and fire.
Wiring
Marking
DC-DC Converter
Flasher Unit
AP6M, APM, and AP1M round flat lenses contain a white
marking plate inside the lens. (AP8M lens cannot be removed.)
DC-DC converters employ an electronic oscillating circuit. Osci-
llating sounds may be heard depending on operating conditions,
but will not affect performance characteristics.
Pierce the round mark on the nameplate on top of the flasher unit
with a flat screwdriver and adjust the variable resistor inside.Turn
clockwise to lengthen the flashing period.
against reverse polarity and a current limiting resistor,
eliminating the need for external resistors.
soldering iron. SnAgCu type lead-free solder is recommended.
When soldering, do not touch the pilot light housing with the
soldering iron. Also ensure that no tensile force is applied to the
terminal. Do not bend the terminal or apply excessive force to
the terminal.
Use a non-corrosive rosin flux.
X2 Negative Terminal
Note: Do not apply excessive force to
Positive Terminal
X1 Positive Terminal
terminals X1 and X2 during wiring.
Nameplate
TOP
Negative Terminal
TOP
(07/03/26)