10250TM36 EATON CUTLER HAMMER, 10250TM36 Datasheet - Page 94

• Manufacturer Part Number: 10250TM36
• Description: Legend Plate
• Manufacturer: EATON CUTLER HAMMER

Specifications of 10250TM36

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• For Use With: 10250T Series Pushbuttons / Indicating Lights
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

47
47-94
Mounting
■
Note: Installation of certain accessories will
increase the total (overall) panel thickness
by the amount shown. The total panel thick-
ness with all accessories installed cannot
exceed the maximum allowable nominal
dimension of 0.27 inch (6.8 mm).
Panel thickness — Inches (mm)
❑
❑
Pushbuttons & Indicating Lights
22.5 mm Heavy-Duty Watertight/Oiltight
E22 and EM22 Series — Dimensions
Nominal: 0.27 (6.8)
– Legend plates, aluminum or
– Locating ring: 0.06 (1.5)
– Large yellow round legend
– Padlockable cover: 0.06 (1.6)
– Rubber boot: 0.05 (1.3)
Minimum: 0.04 (1.0)
plastic: 0.05 (1.3)
plate: 0.04 (1.0)
Table 47-127. Minimum Spacing in Inches (mm)
Figure 47-80. Minimum Spacing in Inches (mm)
Figure 47-81. Rear of Panel Extensions
Table 47-128. Approximate Dimensions in Inches (mm)
Pushbuttons All Types and Push-Pull
Key, Lever and Knob Selector Switches
Size/Type of Operator
All Types up to 1.18 (30) Dia. Including Knob and Key
Lever Operated Selector Switch Operators
1.97 (50) Dia. Operators
Large Yellow Round Legend Plate — 2.76 (70) Dia.
Pushbutton Operators fitted with Rubber Boots or
A
Single Circuit
Block — Full
Voltage and
Resistor Units
2.0 (51)
2.22 (57)
Operated Selector Switches — except those listed below
and 1.18 – 1.57 (30 – 40) Dia. Operators
Padlockable Cover
For more information visit: www.eaton.com
Horizontal spacing for one 3-way and one 5-way mounting adapter.
Horizontal spacing for two 5-way mounting adapters.
3-way adapter
5-way adapter
3-way adapter
5-way adapter
+0.02 (0.4)
0.89 (22.5)
Diameter
Added
Trans.
Block
Dual
Unit
to
B
Dual
Circuit,
Contact
Block
2.6 (66)
2.83 (72)
Contact
Added
Trans.
Block
Unit
to
A
B
Trans.
Light
Unit
C
Trans-
former
Light
Unit
2.91 (74)
3.15 (80)
E
Contact
Circuit
Block
Dual
D
C
D
Trans. Light
Unit and Single
Circuit
Contact Block
3.7 (94)
3.9 (99)
Light Unit
Contact
Block/
0.96 (24.3)
+0.02 (0.4)
B
Dimensions
A
1.18 (30)
1.58 (40)
1.77 (45)
2.16 (55)
2.95 (75)
1.38 (35)
1.58 (40)
-0 (0)
A
Notch Mounting
Hole as Shown
+ _ 0.01 (0.2)
0.13 (3.2)
A
—
1.97 (50)
1.97 (50)
2.16 (55)
2.95 (75)
—
1.97 (50)
E
Trans. Light
Unit and Dual
Circuit
Contact Block
4.3 (110)
4.5 (115)
B
1.97 (50)
1.97 (50)
1.97 (50)
2.16 (55)
2.95 (75)
1.97 (50)
1.97 (50)
CA08102001E
March 2008