HEDS-5540-E12 Avago Technologies US Inc., HEDS-5540-E12 Datasheet
![ENCODER KIT MCW 3CH 200CPR 6MM](/photos/16/35/163587/hedm-5540_wht_sml.jpg)
HEDS-5540-E12
Specifications of HEDS-5540-E12
Related parts for HEDS-5540-E12
HEDS-5540-E12 Summary of contents
Page 1
... This index output electrical degree, high true index pulse which is generated once for each full rotation of the codewheel. The HEDS series utilizes metal codewheels, while the HEDM series utilizes a film codewheel allowing for resolu- tions to 1024 CPR. ...
Page 2
... Package Dimensions HEDS-5500/5540, HEDM-5500/5540 *Note: For the HEDS-5500 and HEDM-5500, Pin # Connect. For the HEDS-5540 and HEDM-5540, Pin #2 is CH. I, the index output. HEDS-5600/5640, HEDM-5600 *Note: For the HEDS-5600 and HEDM-5600, Pin # Connect. For the HEDS-5640, Pin #2 is CH. I, the index output. ...
Page 3
... This output one state width (nominally 90 electri- cal degrees), high true index pulse which is coincident with the low states of channels A and B. Block Diagram Note: Circuitry for only for HEDS-5540, 5640 and HEDM 5540 Three Channel Encoder 3 Definitions Count (N): The number of bar and window pairs or counts per revolution (CPR) of the codewheel. One Cycle (C): 360 electrical degrees (° ...
Page 4
... A will lead channel B. If the codewheel rotates in the clockwise direction, channel B will lead channel A. Output Waveforms 4 HEDS-55XX/56XX HEDM-550X/560X -40°C to 100°C -40°C to +70°C -40°C to 100°C -40°C to +70°C -0 ...
Page 5
... Radial Play (HEDS Series) Shaft Perpendicularity Plus Axial Play (HEDM Series) Shaft Eccentricity Plus Radial Play(HEDM Series) Note: The module performance is guaranteed to 100 kHz but can operate at higher frequencies. 2.7 kΩ pull-up resistors required for HEDS- 5540/5640 and HEDM-5540. Encoding Characteristics Part No. Description ...
Page 6
... Parameter HEDS-5500 Supply Current HEDS-5600 High Level Output Voltage Low Level Output Voltage Rise Time Fall Time HEDS-5540 Supply Current HEDS-5640 High Level Output Voltage HEDM-5500 Low Level Output Voltage HEDM-5600 Rise Time Fall Time HEDM-5500 Supply Current HEDM-5600 High Level Output Voltage ...
Page 7
... The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor shafts. See Ordering Information. 3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in “Encoder Mounting and Assembly”. See also “Mounting Considerations. ” ...
Page 8
... HEDS-8910 Alignment Tool as shown in Encoder Mounting and Assembly. The use of aligning pins or alignment tool is recommend- ed but not required to mount the HEDS-5500 and 5600. If these two channel encoders are attached to a motor with the screw sizes and mounting tolerances specified in the mechanical characteristics section without any Figure 2 ...
Page 9
... Encoder Mounting and Assembly 1a. For HEDS-5500 and 5600: Mount encoder base plate onto motor. Tighten screws step 2. 1b. For HEDS-5540, 5640 and HEDM-5500, 5600, 5540 : Slip alignment tool onto motor shaft. With alignment tool in place, mount encoder baseplate onto motor as shown above. Tighten screws. Remove alignment tool ...
Page 10
... HEDS-5XXX, HEDM-5X0X Series) Molex Figure 5. HEDS-8902 nd 8903 connectors Protective Silicon Cover Protective Silicon Rubber cover gives an extra protection for HEDS-5xx0 and HEDM-5xx0 family when operating in dusty environment. The protective silicon cover is installed to HEDS-5xx0 or HEDM-5xx0 prior to the connector to the encoder is installed. Part Number ...
Page 11
... External Mounting Ears (Included with each order of HEDM-550X/560X two channel encoders and HEDM-554X three Channel encoders) Mounting Type Outputs 5 - Standard Channel 6 - External Channel Mounting Ears (Included with each order of HEDS-554X/564X three channel encoders) 11 HCTL-20xx HOST PROCESSOR DECODER/ COUNTER HCTL-1100 HOST MOTION ...
Page 12
... For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. AV02-1046EN - November 25, 2009 HEDS-5545 HEDS-5600 HEDS-5605 ...