P704-6-S E-Z-Hook, P704-6-S Datasheet - Page 71

• Manufacturer Part Number: P704-6-S
• Description: LEAD TEST PICO HOOK 10/SET 6"
• Manufacturer: E-Z-Hook
• Series: E-Z-PICO-HOOK™r
• Type: Test Leadr

Specifications of P704-6-S

• Wire Gauge: 28 AWG
• Voltage - Rated: 600V
• 1st Connector: Pico Hook
• 2nd Connector: Pico Hook
• Length: 6.000" (152.40mm)
• Current Rating: 1A
• Color: Multiple
• Temperature Range: 221°F (105°C)
• Contents: 10 Leads
• Wire Insulation Material: Poly-Vinyl Chloride (PVC)
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS compliant by exemption

www.e-z z -h h o o o o k.co o m m
E-Z Z -N N AILCLIP™ T T EST TERMINALS
For use with breadboard circuits, experimental hookups and harness board connections, to pretest circuits, modules,
components and burn-in boards.
Use E-Z-Nailclip test terminals to hold wire ends firmly in place for a quick, sure connection. Smooth, tough hook holds
wire ends firmly against the nylon slide without cutting, nicking, or damaging lead wires. E-Z-Nailclips drive into wood
like a nail using the T-20 Tool, or can be pressed into predrilled holes. Products can easily be soldered below board and
simple finger tip operation saves in construction time by speeding wire placement. The rectangular hole design in the slide
eliminates hook rotation. Nailclips are available with a variety of factory-installed adapters.
Colors: Available in 10 colors.
STANDARD T T EST T T ERMINAL
Construction:
One-piece nickel silver shaft and
hook. Durable heat and chemical
resistant nylon slide. Stainless steel
compression coil spring. Requires T-
20 tool to drive into wood or PE-93
Perf-eze adapter to press into
standard perf board holes.
Colors: Available in 10 colors.
ALL M M ETAL T T EST T T ERMINAL F F OR
HIGH T T EMPERATURE U U SE
Construction:
One-piece nickel silver shaft and
hook. Durable heat and chemical
resistant nylon slide. Stainless steel
compression coil spring. Requires T-
20 tool to drive into wood or PE-93
Perf-eze adapter to press into
standard perf board holes.
INSULATION-P P IERCING W W IRE C C LAMP
Part No. Description
81-1 1
Part No. Description
84-1 1
Part No.
82-2 2
Housing:
Lever:
Contact Bolt:
Springs:
High Temperature Hook
Materials a a nd F F inish
Standard Hook
Description
Insulation-Piercing Wire Clamp
Steel; copper, nickel, & tin-plated
Nylon molded in ten different colors
Brass nickel plated
Stainless steel
No need to strip wire end for continuity testing.
Wires can be installed from three different
sides. If more than one wire is to be held in the
same clamp, use the same wire AWG and insert
from the front only, and to the same depth.
68
HEAVY D D UTY T T EST T T ERMINAL
Construction: Three-level copper,
nickel and tin plated tempered
steel hook. Nylon slide. Stainless
steel spring.
Colors: Available in 10 colors.
MULTIPLE W W IRE T T EST T T ERMINAL
Construction:
One-piece nickel silver shaft and
hook. Durable heat and chemical
resistant nylon slide. Stainless steel
compression coil spring. Requires T-
20 tool to drive into wood or PE-93
Perf-eze adapter to press into
standard perf board holes.
Colors: Available in 10 colors.
Part No. Description
Part No. Description
86-1 1
83-8 8
Hook for Multiple Wires
Heavy Duty Hook
Max. Jaw Opening
Mounting Board
Minimum hold
spacing for high
density grouping.