BRT-51X51BM BANNER ENGINEERING, BRT-51X51BM Datasheet - Page 3

• Manufacturer Part Number: BRT-51X51BM
• Description: Reflector
• Manufacturer: BANNER ENGINEERING

Specifications of BRT-51X51BM

• Reflector Type: Square Acrylic Target
• Accessory Type: Reflector
• For Use With: Retroreflective Laser Sensor

Supply Voltage
Sensing Beam
(Laser Characteristics)
Output Configuration
Output Response
Repeatability
Hysteresis
Adjustments
Indicators
Construction
Environmental Ratings
Connections
Operating Conditions
Laser Classification
Application Notes
Certifications
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure. Do
NOT attempt to disassemble this sensor for
repair. A defective unit must be returned to the
manufacturer.
Banner Engineering Corp. • Minneapolis, MN U.S.A
CAUTION . . .
Disassemble for Repair
www.bannerengineering.com • Tel: [phone]
WORLD BEAM
Do Not
10 to 30V dc (10% maximum ripple) at less than 15 mA, exclusive of load;
Protected against reverse polarity and transient voltages
Wavelength: 650 nm visible red Class 1 laser
Pulse Width: 7 microseconds
Rep Rate: 130 microseconds
Average Output Power: 0.065 milliwatts
Solid-state complementary (SPDT); NPN or PNP (current sinking or sourcing), depending on model;
Rating: 100 mA maximum each output at 25°C
Off-state leakage current: NPN: less than 200 µA @ 30V dc (See Application Note 1)
ON-state saturation voltage: NPN: less than 1.6V @ 100 mA
Protected against false pulse on power-up and continuous overload or short circuit of outputs
700 microseconds ON/OFF
NOTE: 200 ms max. delay on power-up; outputs do not conduct during this time
130 microseconds
12% of range typical
Single-turn sensitivity (Gain) adjustment potentiometer
2 LED indicators on sensor top:
Green ON steady: Power ON
ABS housing, acrylic lens cover; 3 mm mounting hardware included
IEC IP67; NEMA 6; UL type 1
2 m (6.5') 4-wire PVC cable
9 m (30') 4-wire PVC cable
Temperature: -10° to +50° C (+14° to +122° F)
Relative Humidity: 90% @ 50° C (non-condensing)
Class 1 laser product; complies with IEC 60825-1:2001 and 21 CFR 1040.10, except for deviations pursuant to Laser Notice
50, dated 7-26-01
1. NPN off-state leakage current is < 200 μA for load resistances > 3 kΩ or optically isolated loads.
For load current of 100 mA, leakage is < 1% of load current
®
QS18LLP Series -
Class 1
Lasers that are safe under reasonably foreseeable
conditions of operation, including the use of optical
instruments for intrabeam viewing.
Reference IEC 60825-1:2001, section 8.2.
Class 1 Laser Characteristics
(see specifications above)
For Safe Laser Use:
• Do not permit a person to stare at the laser from within the beam.
• Do not point the laser at a person’s eye at close range.
• Locate open laser beam paths either above or below eye level, where practical.
PNP: less than 10 µA @ 30V dc
PNP: less than 3.0V @ 100 mA
4-pin Pico-style QD
4-pin Pico-style 150 mm (6") pigtail QD
Specifications
Yellow ON steady: Light sensed
Yellow flashing: Marginal excess gain (1.0 to 1.5x excess gain)
Description of Laser Class
Polarized Retroreflective Laser Sensors
4-pin Euro-style QD
4-pin Euro-style 150 mm (6") pigtail QD
P/N 118900 rev. C
3