OPBA2QD BANNER ENGINEERING, OPBA2QD Datasheet
![no-image](/images/manufacturer_photos/0/0/91/banner_engineering_sml.jpg)
OPBA2QD
Specifications of OPBA2QD
Related parts for OPBA2QD
OPBA2QD Summary of contents
Page 1
Patent 4965548 Figure 1. OMNI-BEAM sensor head and power block bolt and plug together quickly and easily; an optional timing logic module may be added at any time. WARNING . . . Not To Be Used for Personnel Protection ...
Page 2
OMNI-BEAM Sensor Heads Sensor Heads A sensor head module is available for every sensing situation. Sensor heads bolt directly onto the power block, and are fully gasketed for protection against environmental elements. The D.A.T.A. self-diagnostic feature is standard on all ...
Page 3
... OPBTE 2 m (6.5') OPBTEQD 4-Pin Mini QD OPBTEQDH 4-Pin Euro QD AC Voltage (see data sheet p/n 03531 packed with the power block) OPBA2 2 m (6.5') 105-130V ac OPBA2QD 5-Pin Mini QD OPBB2 2 m (6.5') 210-250V ac OPBB2QD 5-Pin Mini QD 0PBAE 2 m (6.5') 105-130V ac OPBAEQD 5-Pin Mini QD OPBBE ...
Page 4
OMNI-BEAM Sensor Heads Sensor Head Programming DIP Switch Settings OMNI-BEAM sensor heads are field-programmable for four operating parameters. To access the four programming DIP switches (see figure 5), remove the sensor block from the power block. Switch #1, Sensing Hysteresis ...
Page 5
Figure 6. OMNI-BEAM D.A.T.A. LEDs Flashing LED Problem Severe moisture is inside the sensor head, caused by condensation or by entry of moisture when the #1 Moisture Alert access cover is removed. High Temperature #2 The temperature inside the sensor ...
Page 6
OMNI-BEAM Sensor Heads Sense and Load LED Indicators The Sense LED indicates when a target has been sensed. When the sensor head is programmed for Light Operate, it lights when the received light signal exceeds the #5 threshold. When programmed ...
Page 7
Figure 8. Dark condition example: D.A.T.A. system LEDs #1 and #2 lit. Figure 9. Light condition example: D.A.T.A. system LEDs #1 through #8 lit. OMNI-BEAM Sensor Heads Measuring Sensing Contrast Contrast is the ratio of the amount of light falling ...
Page 8
OMNI-BEAM Sensor Heads Supply Voltage and Current Supplied by OMNI-BEAM power block Output Response Time See individual sensing heads for response times (page 2) 200 millisecond delay on power-up: outputs are non-conducting during this time. Adjustments OMNI-BEAM sensor heads are ...
Page 9
OSBE & OSBR OSBLV (Opposed) (Retroreflective) 1000 1000 OSBE & OSBR Opposed Mode 100 100 0 ...
Page 10
OMNI-BEAM Sensor Heads OSBE & OSBR OSBLV (Opposed) (Retroreflective) OSBE and OSBR 150 mm 1500 mm Opposed Mode 60 in 100 mm 1000 500 500 mm 20 ...
Page 11
... SMB30MM • Clearance for M6 (1/4") hardware ø30.5 mm ø 6.4 mm (0.25") 57.2 mm (2.25") 25 (1.00") (0.28") (2 Slots) R 25.4 mm 35.1 mm (1.00") (1.38") 69.9 mm (2.75") Accessories Mounting Brackets SMB30UR 13 mm (0.5") 8X #10-32 38.1 mm (1.50" 0 Screw (2) 12.7 mm (0.50") 50.8 mm (2.00") 70.0 mm (2.75") 9.7 mm (0.38" ...
Page 12
... This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 612.544.3164 • Fax: 612.544.3213 • E-mail: sensors@baneng.com Retroreflective Targets ...