FT-SNFM2 PANASONIC EW, FT-SNFM2 Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/5/513/panasonic_ew_sml.jpg)
FT-SNFM2
Manufacturer Part Number
FT-SNFM2
Description
PHOLOELECTRIC SENSOR
Manufacturer
PANASONIC EW
Type
Thrubeamr
Datasheet
1.FV-BR1.pdf
(40 pages)
Specifications of FT-SNFM2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Function table for FX-300 series
Note: Except FX-301B/G/H.
A difference between the updated version unit and the previous version unit for FX-301 (Red LED type)
1. Response times added
2. Extension of timer period
3. Light emitting amount selection function
4. Backup, copy lock and key lock functions added
Peripheral units that can be combined
PRECAUTIONS FOR PROPER USE
m ‘NAVI’ is printed only on the both sides m ‘NAVI’ is printed only on a side
Four-chemical emitting element
Four-chemical emitting element only
Light emitting amount selection function
Reduced intensity mode (S-D)
9,999 digit display
Response time (Max. speed)
Interference prevention function (Effective no. of units)
Independent 2 outputs
Alarm output function
Error output function
Differential sensing
Window comparator mode
Checking minor changes between previous and new models can be
done by checking whether the printing is on both sides or only one side.
Changes in appearance
Upgraded functions
FX-CH(-P)
FX-CH2(-P)
SC-GU1-485
Top view
4 steps
Side view
An ultra high-speed mode (H-SP) has been added to the existing 4 response time modes
[high-speed (FAST), reduced intensity (S-D), standard (STD) and long range (LONG)].
This is changed using ‘
The setting range for the timer period was previously 500 ms, but
this has been extended to a new range of 9999 ms.
The light emitting amount can be changed to one of 4 levels
(5 levels when emission halt is included).
Backup: This selects whether or not threshold values set by
Copy lock: This selects whether copy function and data bank
Key lock: This disables input using switches to prevent accidental
Display
Uses special parts
Name
plate
Before change
Before change
teaching are written to (stored in) an EEPROM.
changing of settings.
function communication are possible or not.
150 !s (FAST)
250 !s (S-D)
250 !s (STD)
2 ms (LONG)
APC circuit
’ in ‘
(Previous version unit)
5 steps
Side view
Top view
Incorporated (4)
’.
FX-301(P)
150 !s
Added to
name plate
g
g
g
After change
After change
(Note 1)
(Note 1)
65 ¨s (added)(H-SP)
150 !s (FAST)
250 !s (S-D)
250 !s (STD)
2 ms (LONG)
Change in shape
of jog switch
Previous models
Incorporated (8)
FX-302(P)
300 !s
g
g
g
g
Not incorporated (0)
Refer to the ‘Sensor general catalog 2003-2004’ for fiber precautions.
Communication possible
1. Timer selection method
2. Checking threshold value in RUN mode
1. Checking blinking of sensitivity surplus
2. Initial direct code value changed
1. Addition of an APC circuit
Previous
version unit
Changes in operation
Display changes
Internal circuit changes
Points to note when combining sensor types
FX-303(P)
The threshold values can be checked by turning the jog switch.
The stable surplus display method after teaching has been changed.
The factory default settings for the direct codes have been changed.
m The default setting for the timer period is 10 ms, and the direct code for
A four-chemical emitting element which provides stable sensing over long periods has been
added, as well as an APC (Auto Power Control) circuit that improves stability during short periods.
When using the newer sensors together with previous version
units (including the FX-301B/G/H), note the following.
•
•
•
Previous version unit: Timer type was changed using PRO1 mode. The ‘TIMER’
After change: The type of timer can be changed using the ‘TIMER’ function in NAVI mode.
Communication is possible when the previous version units and
the updated version units are used in an arrangement such as
that shown in Figure A below.
If the previous version units and the updated version units are used in
an arrangement such as that shown in Figure B below, the interference
prevention function and the PRO4 function cannot be used.
In order to use the interference prevention function and the PRO4 function when
using previous version units and the updated version units together, it is
recommended that you use an arrangement such as that shown in Figure C below.
<
90 !s
Previous version unit
Figure A
g
10 ms is ‘4’, so this has been changed.
Previous version unit: Sensitivity surplus is indicated by the number
After change
Updated
version unit
O.K.
>
(Updated version unit)
Incorporated (4)
FX-301(P)
Communication impossible
Updated
version unit
setting in NAVI mode could only be turned on or off.
65 !s
Digital display only
g
g
g
g
g
<
of blinks of the stability indicator.
Figure B
0000
Previous
version unit
N.G.
>
Not incorporated (0)
FX-301(P)-HS
New models
35 !s
After change
g
g
g
Previous
version unit
<
1234567890ABCDEF
Figure C
Incorporated (16)
FX-300
>
Updated
version unit
FX-305(P)
65 !s
0004
g
g
g
g
g
g
g
g
g
g
34