Q85VR3LP-T9 BANNER ENGINEERING, Q85VR3LP-T9 Datasheet - Page 6

• Manufacturer Part Number: Q85VR3LP-T9
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Polarized Retroreflectiver

Specifications of Q85VR3LP-T9

• Sensing Range: 0m To 4.6m
• Output Current: 3A
• Sensor Output: SPDT-Relay
• Sensing Range Max: 4.6m
• Supply Voltage Dc, Max: 240V
• Supply Voltage Ac, Max: 240V
• Fiber Optic Applications: Conveyor Control
• Fiber Optic Sensor Type: Polarized Retroreflective

Q85 Sensors
6
Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time and
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Operating Conditions
Vibration and
Mechanical Shock
Certifications
P/N 137791
Q8562E Emitter
1
2
3
4
5
10 to 48V dc at 50 mA max. exclusive of load; Q8562E emitter requires 25 mA
Protected against reverse-polarity
Q85BB62.. models: NPN sinking and PNP sourcing outputs, ON/OFF output
Q85BB62..-T9 models: NPN sinking and PNP sourcing outputs, selectable timer
Standard outputs are solid-state, one NPN, one PNP; 150 mA max. (at 25°C, either output).
Derate output by 1 mA/°C above 25°C
Off-state leakage current: <1 µA
Output saturation voltage: <1V at 10 mA and <2V at 150 mA
The two standard outputs may be used simultaneously (max. load 150 mA each output)
Low-saturation voltage alternative NPN output is provided for easy interfacing to TTL and similar circuitry
Output saturation voltage: <200 millivolts at 10 mA and <1V at 150 mA
Overload and short circuit protected
This output is not reverse-polarity protected
Protected against false pulse on power-up, overload and short circuit of outputs
Response time and repeatability are independent of signal strength:
Single-turn Sensitivity control potentiometer, accessible beneath the ABS wiring chamber cover. Timing logic (for “T9”
models) is configured via DIP switch. Pulse length and delay are set via single-turn potentiometer (under the wiring
chamber cover). The adjustable time range for both functions is 0.1 to 5 seconds; both functions are automatically set
to the same value. All models have a light/dark operate switch under the wiring chamber cover.
Exclusive Alignment Indicating Device system (AID™) lights a red LED indicator whenever the sensor sees its own
modulated light, and pulses at a rate proportional to the strength of the light signal. Yellow indicator lights whenever
the sensor’s output is energized.
Yellow ABS housing, acrylic lenses, and steel-plated hardware.
Maximum wire size (for connection to wiring terminals) is #14 AWG.
Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 6P, 12, and 13; IEC IP67
Temperature:
Max. Relative Humidity: 90% at 50°C (non-condensing)
Meets Mil. Std. 202F requirements.
Method 201A (Vibration: frequency 10 to 55 Hz max., douple-amplitude 0.06”, max. acceleration 10G)
Method 213B conditions H & I (Shock: 75G with unit operating; 100G for non-operation)
10-48V dc
Q85BB62R
Q85BB62LP
Q85BB62D
Q85BB62DL
*ON/OFF operation (no timing in use)
+
–
Model
NRTL/C
Q85BB62 Model Specifications
Response Time Repeatability
1 ms
1 ms
1 ms
2 ms
Q85BB62 Model Hookups
Q85BB62 Standard
–25° to +55°C (–13° to +131°F)
1
2
5
4
3
Load
Load
125 µs
250 µs
250 µs
500 µs
10-48V dc
+
–
Banner Engineering Corp. • Minneapolis, MN U.S.A.
Q85BB62R-T9
Q85BB62LP-T9
Q85BB62D-T9
Q85BB62DL-T9
Alternative Low Saturation Sinking (NPN) Hookup
www.bannerengineering.com • Tel: [phone]
Model*
1
2
5
4
3
Response Time Repeatability
8 ms
8 ms
8 ms
8 ms
NOTE: This hookup provides a direct
interface to TTL and similar circuits.
CAUTION: The output is NOT
reverse-polarity protected in this
wiring configuration.
Load
10-48V dc
+
–
1 ms
1 ms
1 ms
1 ms