QS18VP6LAF250Q BANNER ENGINEERING, QS18VP6LAF250Q Datasheet - Page 5

• Manufacturer Part Number: QS18VP6LAF250Q
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Series: QS18 Adjustable-Fieldr

Specifications of QS18VP6LAF250Q

• Output Current: 100mA
• Sensor Output: PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensing Range Min: 0mm
• Sensor Input: Laser
• Supply Voltage Max: 30VDC
• Sensing Range Max: 20mm

Supply Voltage
Sensing Beam
Laser Characteristics
Output Configuration
Output Response
Repeatability
Sensing Hysteresis
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Laser Classification
Application Notes
Certifications
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
10 to 30V dc (10% maximum ripple)
at less than 25 mA, exclusive of load;
Protected against reverse polarity and
transient voltages
Visible red LED, 660 nm
N/A
Solid-state complementary (SPDT);
NPN or PNP (current sinking or
sourcing), depending on model;
Rating: 100 mA maximum each output
at 25° C
Off-state leakage current: less than 50
µA @ 30V dc
ON-state saturation voltage: less than
1V @ 10 mA; less than 1.5V @ 100 mA
Protected against false pulse on power-
up and continuous overload or short
circuit of outputs
700 microseconds ON/OFF;
100 ms delay on power-up; outputs do
not conduct during this time
175 microseconds
0.5% of range typical at 20 mm cutoff
1% of range typical at 50 mm cutoff
3% of range typical at 100 mm cutoff
Five-turn adjustment screw sets cutoff distance between min. and max. positions, clutched at both ends of travel
2 LED indicators on sensor top:
Green ON steady: Power ON
ABS housing, acrylic lens cover;
2.5 mm and 3 mm mounting hardware included
IEC IP67; NEMA 6; UL Type 1
2 m (6.5') 4-wire PVC cable, 9 m (30') PVC cable, or 4-pin Pico-style or Euro-style 150 mm (6") pigtail QD, depending on
model
Temp: 0° to +55° C (+32° to 131° F)
Relative Humidity: 95% @ 50° C (non-condensing)
N/A
1. NPN off-state leakage current is < 200 μA for load resistances > 3 kΩ or optically isolated loads.
For load current of 100 mA, leakage is < 1% of load current
QS18AF Models
WORLD-BEAM
Specifications
Yellow ON steady: Light sensed
Yellow flashing: Marginal excess gain (1 to 1.5x excess gain)
10 to 30V dc (10% maximum ripple) at less than 15 mA, exclusive of load;
Protected against reverse polarity and transient voltages
Visible red laser (see below)
Wavelength: 650 nm visible red Class
1 laser
Pulse Width: 7 microseconds
Rep Rate: 130 microseconds
Average Output Power: 0.065 mW
Solid-state complementary (SPDT); NPN or PNP (current sinking or sourcing),
depending on model;
Rating: 100 mA maximum each output at 25° C
Off-state leakage current:
ON-state saturation voltage:
Protected against false pulse on power-up and continuous overload or short
circuit of outputs
700 microseconds ON/OFF;
200 ms delay on power-up; outputs do not conduct during this time
130 microseconds
1% of range typical at 30 mm cutoff
2% of range typical at 75 mm cutoff
5% of range typical at 150 mm cutoff
Temp: −10° to +50° C (+14° to 122° F)
Class 1 laser product
Complies with IEC 60825-1:2001 and 21 CFR 1040.10, except for deviations
pursuant to Laser Notice 50, dated 7-26-01
®
QS18LAF Models
QS18 Adjustable-Field Sensors
NPN: less than 200 µA @ 30V dc (See Application Note 1)
PNP: less than 10 µA @ 30V dc
NPN: less than 1.6V @ 100 mA
PNP: less than 3.0V @ 100 mA
Wavelength: 658 nm visible red Class
2 laser
Pulse Width: 7 microseconds
Rep Rate: 130 microseconds
Average Output Power: 0.2 mW
1% of range typical at 50 mm cutoff
2% of range typical at 150 mm cutoff
5% of range typical at 250 mm cutoff
Class 2 laser product
QS18LAF250 Models
approval in process
P/N 66981 rev. G
5