Q236E BANNER ENGINEERING, Q236E Datasheet - Page 3

• Manufacturer Part Number: Q236E
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Opposed Moder

Specifications of Q236E

• Output Current: 150mA
• Supply Voltage Range Dc: 10V To 30V
• Contact Current Max: 150mA
• Switch Terminals: Cable
• Peak Reflow Compatible (260 C): No
• Sensor Housing: Rectangular
• Sensor Input: Optical
• Body Style: Rectangular
• Brand/series: Q23
• Current, Switching: 150 mA
• Ip Rating: IP67
• Mounting Type: Bracket
• Primary Type: Photoelectric
• Range, Measurement: 8 m
• Sensing Mode: Opposed
• Technology: Photoelectric
• Termination: 4-Wire Cable
• Voltage, Supply: 30 VDC
• Sensing Range Max: 8m
• Leaded Process Compatible: No
• Lead Free Status / Rohs Status: RoHS Compliant part

Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Q(H)23SN6xx models: NPN sinking, N.O. (normally open) & N.C. (nor-
Q(H)23SP6xx models: PNP sourcing, N.O. & N.C. complementary
Output Rating
Off-state leakage current less than 1 microamp at 30V dc
Output saturation voltage less than 1 volt at 10 mA dc; less than 1.5V
Output Protection Circuitry
Output Response Time
10 to 30V dc (10% maximum ripple) at less than 25 mA (exclusive of load)
(Opposed emitters and receivers draw 20 mA each)
Protected against reverse polarity and transient voltages
Solid-state dc complementary outputs:
mally closed) complementary
Light operate: N.O. output conducts when the sensor sees its own
modulated light source
Dark operate: N.C. output conducts when the sensing beam is
blocked
The N.C. output may be used as an alarm output, depending upon
hookup to the power supply (see hookup diagrams)
150 mA maximum each in standard hookup; when wired for alarm out-
put, the total load may not exceed 150 mA
at 150 mA dc
Protected against false pulse on power-up and continuous overload
or short-circuit of outputs
1 millisecond on and off
(FPY model high-speed sensors: 100 microsecond response time)
NOTE: 100 ms delay on power-up; outputs do not conduct during
this time.
Q23 and QH23 Series
Specifications
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Application Note
All opposed sensors: 0.13 ms
FPY model high-speed sensors: 25 microseconds
All other models: 0.25 ms
Response time and repeatability specifications are independent of
signal strength.
Sensitivity control (single-turn, o-ring sealed potentiometer)
Emitters: green Power ON indicator
All others: green Power ON and yellow Output indicators
Reinforced thermoplastic polyester housing, completely sealed,
o-ring seal, acrylic lenses; stainless steel screws and mounting
bracket.
Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67.
Housing materials rated UL 94 V-0.
PVC-jacketed 4-conductor 2 m (6.5') or 9 m (30 ') cables, or 6" pigtail
with 4-pin Pico-style quick disconnect (QD) fitting are available. Mating
QD cables are ordered separately.
Temperature: -20° to +55°C (-5° to +131°F)
Max. rel. humidity: 90% at 50°C (non-condensing)
To avoid damage to the sensor caused by static discharge (ESD),
use the plastic screwdriver supplied with each sensor (included in
the hardware packet) to adjust the sensitivity control. Otherwise, use
a screwdriver with an insulated handle.