QS186LE BANNER ENGINEERING, QS186LE Datasheet - Page 4

• Manufacturer Part Number: QS186LE
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of QS186LE

• Supply Voltage Range Dc: 10V To 30V

WORLD BEAM QS186LE Laser Emitter
Figure 5. At long distances, use retroreflective
4
Laser Emitter
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure; per
EN 60825. DO NOT attempt to disassemble
this sensor for repair. A defective unit must be
returned to the manufacturer.
P/N 109415 rev. F
CAUTION
tape to locate the beam at the desired
location.
Target
Never use a mirror as an
alignment target.
Receiver
Class 1
Lasers that are safe under reasonably foreseeable conditions of operation, including the use
of optical instruments for intrabeam viewing.
Reference 60825-1 Amend. 2 © IEC:2001(E), section
8.2.
Class 1 Laser Characteristics:
Wavelength = 650 nm
Pulse Power ≤ 1.9 milliwatts
Pulse Width = 5 microseconds
Rep Rate = 27 microseconds
Class 2
Low-power lasers are by definition incapable of causing eye injury within the duration of the
blink (aversion response) of 0.25 seconds. They also must emit only visible wavelengths
(400–700 nm). Therefore, an ocular hazard can exist only if an individual overcomes their
natural aversion to bright light and stares directly into the laser beam.
For safe laser use:
• D o not permit a person to stare at the laser from within the beam.
• D o not point the laser at a person’s eye at close range.
• T he beam emitted by a Class 2 laser product should be terminated at the end of its useful
Class 2 Laser Characteristics:
Wavelength = 650 nm
Pulse Power ≤ 4.8 milliwatts
Pulse Width = 5 microseconds
Rep Rate = 27 microseconds
To mount the QS186LE into bracket models SMB18A or SMB46A, insert the laser emitter into
the hole in the bracket, then tighten the hex jam nut to the bracket, so the emitter is held
snugly in place. Mount the bracket using your own screws or bolts (SMB18A uses M4 or #8
screws or bolts; SMB46A uses M5 or #10), and check for alignment, as described on pages 2
and 3.
If using the adjustable bracket (model SMB46A), tighten or loosen one or two of the precision
alignment screws (use the supplied 2 mm Allen wrench) until the laser is accurately aligned.
path. Open laser beam paths should be located
above or below eye level where practical.
Description of Class 1 and Class 2 Lasers
NOTES:
1. 1 MIL. WHITE POLYESTER WITH PERMANENT ADHESIVE, LAMINATED WITH 1 MIL. CLEAR
2. LETTERING & GRAPHICS TO BE CENTERED ON LABEL AND MUST NOT BE TOUCHING EDGE OF
3. USE DIMENSION DRAWING:
4. MAXIMUM DEVIATION FROM ART WORK +/- .05mm.
5. MUST MEET CSA GROUP VIII PLASTICS LABEL REQUIREMENTS.
6. MUST BE UL RECOGNIZED CONSTRUCTION.
LABEL NOR BE CUT OFF.
POLYESTER. ALL COLORS MUST BE OPAQUE. COLOR BREAKS AS SHOWN. USE ADOBE
ILLUSTRATOR FILE 126390.AI. PMS COLORS ARE: YELLOW = PMS 108C & BLACK.
Installation
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
70551.DWG (AUTOCAD)
CLASS 2 LASER PRODUCT
Pulse Power < 4 mW, 645 - 665 nm, 35 kHz,
5.1 uS Pulse. Complies TO 21 CFR 1040.10 &
EN60825-1:2001 except for deviations pursuant
to laser notice No. 50, dated 7-26-01.
LASER LIGHT - DO NOT STARE INTO BEAM