QS30LLPCQ BANNER ENGINEERING, QS30LLPCQ Datasheet - Page 8

• Manufacturer Part Number: QS30LLPCQ
• Description: OPTICAL SENSOR
• Manufacturer: BANNER ENGINEERING
• Type: Retroreflectiver

Specifications of QS30LLPCQ

• Sensing Range: 0.2m To 18m
• Output Current: 150mA
• Sensor Output: Bipolar NPN / PNP
• Supply Voltage Range Dc: 10V To 30V
• Primary Type: Photoelectric

WORLD-BEAM
8
Supply Beam
Beam Size at Aperture
Laser Classification
Supply Voltage
Supply Protection Circuitry
Delay at Power-Up
Output Configuration
Output Rating
Output Protection
Output Response Time
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Vibration and Mechanical
Shock
Certifications
P/N 112355 rev. A
®
QS30 Series –
650 nm visible red
Approx. 3 mm
Class 1
10 to 30V dc (10% max. ripple @ 10% duty cycle) @ 35 mA max current, exclusive of load
Protected against reverse polarity, over voltage, and transient voltages
1 second max.; outputs do not conduct during this time
Bipolar: 1 current sourcing (PNP) and 1 current sinking (NPN)
150 mA maximum load
OFF-state leakage current: < 10 µA at 30V dc
ON-state saturation voltage:
Protected against output short-circuit, continuous overload, transient over-voltages, and false pulse on
power-up
500 microseconds
70 microseconds
2 push buttons and remote wire
• Easy push-button configuration
• Manually adjust (+/–) thresholds (push buttons only)
• LO/DO and OFF-delay configuration options
• Push-button lockout (from remote wire only)
Green LED: Power ON
Yellow LED: Output conducting
8-Segment Red Bargraph
ABS plastic housing; acrylic lens cover
IP67, NEMA 6
5-conductor 2 m (6.5') PVC cable, 9 m (30') PVC cable, or 5-pin integral Euro-style quick-disconnect fitting
Temperature: -10° to +50°C (+14° to 122°F)
Max. relative Humidity: 90% @ 50°C (non-condensing)
All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max. double amplitude
0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G, 11 ms duration, half sine wave.
SETUP mode: LED 3
RUN mode: Signal strength (excess gain), relative to switchpoint
Sensor calibration failure: Alternating even-numbered and odd-numbered LEDs flash
NPN: < 1.0V @ 150 mA load
PNP: < 2.0V @ 150 mA load
LED 2 (DO): Flashes Red when Dark Operate is selected
LED 1 (LO): Flashes Red when Light Operate is selected
Model QS30LLP
LED 8: >6X
LED 7: 5-6X
LED 6: 4-5X
LED 5: 3-4X
LED 4: 2-3X
LED 3: 1-2X
LED 2: 0.5-1X
LED 1: 0-0.5X
: Flashes Red when delay is selected
Specifications
Polarized Retroreflective Laser Sensors
Model QS30LLPC
LED 8: >2X
LED 7: 1.5-2X
LED 6: 1-1.5X
LED 5: 0.8X
LED 4: 0.6X
LED 3: 0.4X
LED 2: 0.2X
LED 1: 0X
Banner Engineering Corp.
www.bannerengineering.com • Tel: [phone]
Factory Defaults:
• No Delay
• Dark Operate
• Push buttons enabled
•
Minneapolis, MN U.S.A.