D6X39B222 MULTICORE (SOLDER), D6X39B222 Datasheet
![SOLDER WIRE, X39, 22SWG, 250G](/photos/20/82/208299/42257630_sml.jpg)
D6X39B222
Manufacturer Part Number
D6X39B222
Description
SOLDER WIRE, X39, 22SWG, 250G
Manufacturer
MULTICORE (SOLDER)
Datasheet
1.1399075-M.pdf
(2 pages)
Specifications of D6X39B222
External Diameter
0.71mm
Material Composition
Sn60Pb40
Melting Temperature
188°C
Weight
250g
Wire Size Swg
22SWG
Bit Temperature
308°C
Flux Type
X39, Rosin Based, Halide Free
Reel Length
RoHS Compliant
Outer Diameter
0.71mm
Solder Alloy
60/40 Sn/Pb
Solder Gauge Swg
22SWG
Rohs Compliant
No
NO CLEAN CORED SOLDER WIRE FLUX
Properties of Multicore X39 solid flux for cored
solder wires:
PRODUCT RANGE
Multicore X39 cored wires are manufactured as
standard with a nominal flux content of 1%.
Multicore X39 cored wires are available in a variety of
alloys conforming to J-STD-006 and EN 29453 or
alloys conforming to similar national or international
standards. For details refer to document “Properties of
Alloys used in Cored Solder Wires ”. A wide range of
wire diameters is available.
TECHNICAL SPECIFICATIONS
A full description of test methods and detailed test
results are available on request.
Alloys: The alloys used for Multicore flux cored solder
wires conform to the purity requirements of the
common national and international standards. A wide
range of wire diameters is available manufactured to
close dimensional tolerances. For details refer to
document “Properties of Alloys used in Cored Solder
Wires ”.
Flux: Multicore X39 solid flux is based on modified
rosins and halide free carboxylic acid activators. In use
it has a mild rosin smell and leaves a small quantity of
clear residue. It may be classified as RO L0 according
to J-STD-004 (January 1995), LR3CN according to
IPC-SF-818 or DIN F-SW32 according to DIN 8511. It
meets the requirements of Bellcore TR-NWT-000078
issue 3 (December 1991).
THE TECHNICAL INFORMATION CONTAINED HEREIN IS INTENDED FOR REFERENCE ONLY. PLEASE CONTACT HENKEL
TECHNOLOGIES TECHNICAL SERVICE FOR ASSISTANCE AND RECOMMENDATIONS ON SPECIFICATIONS FOR THIS
No clean
Low residue
Eliminates cost of cleaning
Halide free
Non-corrosive formulation
Negligible residues
Fast Soldering on copper and brass
NOT FOR
PRODUCT SPECIFICATIONS
PRODUCT.
TEST
Acid value
Halide content
Copper mirror
Chromate paper
Corrosion
Test
SPECIAL PROPERTIES
The uncleaned residues PASS SIR testing to the
Bellcore TR-NWT-000078 issue 3 (December 1991)
and IPC Class 1,2 and 3 protocols. They also pass the
electromigration test specified by Bellcore TR-NWT-
000078.
Test conditions
Test time, h
Surface insulation
resistance, ohms
Passmark, ohms
Test conditions
Test time, h
Surface insulation
resistance, ohms
Passmark, ohms
Test conditions
Test time, h
Bias, V (DC)
Surface insulation
resistance, ohms
Unfluxed control, ohms
ELECTROMIGRATION TEST RESULTS ON UNCLEANED COMBS
BELLCORE TR-NWT-000078 ISSUE 3
SIR TEST RESULTS ON UNCLEANED COMBS
BELLCORE TR-NWT-000078 ISSUE 3
SIR TEST RESULTS ON UNCLEANED COMBS
FLUX PROPERTIES
J-STD-004
IPC-SF-818
BS 5625
DTD 599A
DIN 8516
JIS-Z-3197
Multicore X39
1.63 x
10
0
-
12
IPC-SF-818
3.17 x 10
1.68 x
10
10
24
24
-
85°C, 85% RH
1.16 x 10
5.09 x 10
9
8
No bias
35°C, 85% RH
Technical Data Sheet
11
96
85°C, 85% RH
3.37 x 10
215mg KOH/g
Pass (10 days)
September 2007
10
9
9
RESULT
96
8
Zero
Pass
Pass
Pass
Pass
Pass
Pass
Pass
3.52 x 10
9
5.43 x 10
8.91 x 10
10
96
3.43 x 10
500
11
10
168
10
11
8
9
9
9
D6X39B222 Summary of contents
Page 1
... Multicore X39 cored wires are available in a variety of alloys conforming to J-STD-006 and EN 29453 or alloys conforming to similar national or international standards. For details refer to document “Properties of Alloys used in Cored Solder Wires ”. A wide range of wire diameters is available. TECHNICAL SPECIFICATIONS A full description of test methods and detailed test results are available on request ...
Page 2
... Do not apply excessive solder or heat to the joint as this may result in dull, gritty fillets and excessive or darkened flux residues. Remove solder wire from the work piece and then remove the iron tip ...