D4NS1AF Omron, D4NS1AF Datasheet - Page 11

• Manufacturer Part Number: D4NS1AF
• Description: SWITCH, SAFETY INTERLOCK, 1NC/1NO, 10A
• Manufacturer: Omron
• Type: Door Switchr

Specifications of D4NS1AF

• Contact Configuration: DPST-1NO / 1NC
• Contact Voltage Ac Max: 240V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 2.5A
• Switch Terminals: Screw
• Switch Function Configuration: N.O./N.C.
• Current Rating (max): 3A
• Operating Temp Range: -30C to 70C
• Lead Free Status / Rohs Status: Compliant

Wiring
Wiring
<Reference>
The crimp terminals listed below have a thickness of 0.5 mm or less.
• When connecting with insulation tubes and M3.5 crimp terminals,
• Do not push the crimp terminal and the likes into the opening
• Use terminals having the thickness of 0.5 mm or less to avoid the
J.S.T. Mfg Co.
Manufacture
connect the terminals as shown in the following figure and wire
without overriding to the case and the cover. Adequate conductor
size is AWG 20 to AWG18 (0.5 to 0.75 mm
Prepare lead wires using the lengths given in the following
diagrams. If lead wires are too long, they will press against the
cover causing the cover to not close properly.
between the parts to prevent the case from being broken and
deformed.
contact between the terminal and the Switch case inside.
J.S.T is a Japanese manufacturer.
1-Conduit Models with 3 Poles
2-Conduit Models with 3 Poles
Crimp terminal
dz dia.: 3.7 mm
D dia.: 2.9 mm
A
C
E
A
C
E
Correct
B: 6.6 mm
L: 19 mm
F: 7.7 mm
I :
t: 0.5 mm
Terminal screw
11
21
33
11
21
33
8.0 mm
12
22
34
12
22
34
FN0.5-3.7 (F Type)
N0.5-3.7 (Straight Type)
B
D
D dia.
F
D
B
F
42 mm
Type
E
E
C
l
C
A
A
B D F
B
Left hand
D
F
Tolerance ±2 mm
28 mm
Tolerance ±2 mm
L
28 mm
Incorrect
F
33 mm
dz dia.
Right hand
28 mm
42 mm
2
).
E
C
A
B D F
B
Tolerance ±2 mm
42 mm
Contact Arrangement
(Screw terminal type)
(Connector type)
Socket Tightening (Models with Connectors)
Conduit Opening
Recommended Connectors
Use the connector with thread section of 9 mm long or less. If a
connector with a longer thread section is used, the protruding part
may interfere with the other parts inside the body. Use the connectors
listed below to ensure IP67 degree of protection.
When use LAPP's products, use together with a Seal Packing which
is sold separately (Type names, JPK-16, GP-13.5, or GPM20) and
tighten with proper tightening torque.
• The contact arrangements are shown below.
• Suitable socket is XS2F-D421 series (OMRON).
• Refer to the Connector Catalog for corresponding Socket pin
• Turn the tightening screws on the Socket by hand and tighten them
• Make sure that the Socket’s connector is tightened securely,
• When using 1/2-14NPT conduits, apply sealing tape between the
• Use cables with suitable diameters for the connector being used.
• When wiring, place the enclosed cap screw on unused conduit
• LAPP is a German manufacturer.
• Before using a 2-conduit type 1/2-14NPT connector, attach the
G1/2
Pg13.5
M20
1/2-
14NPT
numbers and lead wire colors.
until the gap between the Socket and Plug essentially disappears.
otherwise the rated degree of protection (IP67) of the D4NS may
not be maintained, or the Socket connector may be loosened by
vibration.
connector and conduit opening to maintain the degree of protection
(IP67) of the Switch.
openings (for 2-Conduit Switches) and tighten them to the suitable
tightening torque.
enclosed adapter to the Switch, and used the above connector.
Size
2
1
3
D4NS-@BF (2NC)
D4NS-@DF (3NC)
11
21
31
11
31
4
LAPP
LAPP
LAPP
LAPP
Zb
Zb
Manufacture
D4NS-9BF (2NC)
1 (11)
3 (31)
12
22
32
12
32
Zb
2 (12)
4 (32)
ST-PF1/2
5380-1002
S-13.5
5301-5030
ST-M20 × 1.5
5311-1020
ST-NPT1/2
5301-6030
D4NS-@CF (2NC/1NO)
D4NS-@FF (2NC/1NO (MBB))
D4NS-@AF (1NC/1NO)
D4NS-@EF (1NC/1NO (MBB))
11
21
33
11
33
Pin No. (Terminal No.)
Model
Zb
Zb
D4NS-9AF (1NC/1NO)
D4NS-9EF (1NC/1NO (MBB))
1 (11)
3 (33)
12
22
34
12
34
Zb
6.0 to 12.0 mm
6.0 to 12.0 mm
7.0 to 13.0 mm
6.0 to 12.0 mm
Applicable cable
2 (12)
4 (34)
diameter
D4NS
11