PAXCDS40 Red Lion Controls, PAXCDS40 Datasheet - Page 4

• Manufacturer Part Number: PAXCDS40
• Description: Quad Setpoint Sourcing Open Collector Output Interface Card
• Manufacturer: Red Lion Controls

Specifications of PAXCDS40

• Accessory Type: Quad Setpoint Sourcing Open Collector Output Interface Card
• Accuracy: ± 0.01% + 10 ms
• Brand/series: PAX Series
• Card Type: Quad Setpoint Sourcing Open Collector Output Card
• Standards: cULus Listed, CSA Certified and CE Marked
• For Use With: Red Lion PAX Digital Input Panel Meters
• Lead Free Status / RoHS Status: na

Red Lion Controls
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
Enter the time value in seconds that the alarm is delayed
from turning on after the trigger point is reached. A value of
0.0 allows the meter to update the alarm status per the
response time listed in the Specifications. When the output
logic is
accumulated at power-off resets during power-up.
Enter the time value in seconds that the alarm is delayed
from turning off after the trigger point is reached. A value of
0.0 allows the meter to update the alarm status per the
response time listed in the Specifications. When the output
logic is
accumulated at power-off resets during power-up.
Enter the output logic of the alarm output. The
leaves the output operation as normal. The
reverses the output logic. In
Setpoint Alarm Figures are reversed.
Enter the reset action of the alarm output.
output to automatically reset off at the trigger points per the
Setpoint Action shown in Setpoint Alarm Figures. The “on”
alarm may be manually reset (off) immediately by a front
panel function key or user input.The alarm remains reset off
until the trigger point is crossed again.
latches the alarm output on at the trigger point per the
Setpoint Action shown in Setpoint Alarm Figures. Latch
means that the alarm output can only be turned off by front
panel function key or user input manual reset, serial reset
command or meter power cycle. When the user input or
function key is activated (momentary or maintained), the
corresponding “on” alarm output is reset immediately and
remains off until the trigger point is crossed again.
(Previously latched alarms will be off if power up Display
Value is lower than setpoint value.)
the alarm output on at the trigger point per the Setpoint
Action shown in Setpoint Alarm Figures. Latch means that
the alarm output can only be turned off by front panel
function key or user input manual reset, serial reset
command or meter power cycle. When the user input or
function key is activated (momentary or maintained), the
meter delays the event until the corresponding “on” alarm
output crosses the trigger off point. (Previously latched
alarms are off if power up Display Value is lower than
setpoint value. During a power cycle, the meter erases a
previous Latch 2 reset if it is not activated at power up.)
When
trigger point is crossed. Once the alarm is on, the alarm
operates normally per the Setpoint Action and Reset Mode.
STANDBY OPERATION
= Automatic action; This action allows the alarm
= Latch with delay reset action; This action latches
= Latch with immediate reset action; This action
OFF TIME DELAY
ON TIME DELAY
OUTPUT LOGIC
RESET ACTION
, the alarm is disabled (after a power up) until the
, this becomes off time delay. Any time
, this becomes on time delay. Any time
Auto
0. 0
0. 0
nor
no
to
to
3275. 0
3275. 0
LAtC1
YES
rEv
, the alarm states in the
Sec
Sec
LAtC2
NL - 3821 AD Amersfoort
Fax [phone]
Tel [phone]
Red Lion Controls BV
logic
logic
Printerweg 10
4
Alternate Setpoints
Alternate list allows an additional set of setpoint values. (The setpoint numbers
nor rear terminal numbers will change in the Alternate list.) The Alternate list
can only be activated through a function key or user input programmed for
in Module 2. When the Alternate list is selected, the Main list is stored and
becomes inactive. When changing between Main and Alternate, the alarm state
of Auto Reset Action alarms will always follow their new value. Latched “on”
alarms will always stay latched during the transition and can only be reset with
a user input or function key. Only during the function key or user input
transition does the display indicate which list is being used.
The Company warrants the products it manufactures against defects in materials and
workmanship for a period limited to two years from the date of shipment, provided the
products have been stored, handled, installed, and used under proper conditions. The
Company’s liability under this limited warranty shall extend only to the repair or
replacement of a defective product, at The Company’s option. The Company disclaims all
liability for any affirmation, promise or representation with respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify
RLC against damages, claims, and expenses arising out of subsequent sales of RLC
products or products containing components manufactured by RLC and based upon
personal injuries, deaths, property damage, lost profits, and other matters which Buyer, its
employees, or sub-contractors are or may be to any extent liable, including without
limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and
liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-
637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products
except those expressly contained herein. The Customer acknowledges the disclaimers and
limitations contained herein and relies on no other warranties or affirmations.
An Alternate list of setpoint values can be stored and recalled as needed. The
PROBE BURN-OUT ACTION (PAXT ONLY)
The
of “on” alarm outputs. The
corresponding setpoint annunciators of “off” alarms
outputs. The
setpoint annunciators of “on” alarm outputs.
Enter the probe burn-out action. In the event of a
temperature probe failure, the alarm output can be
programmed to go on or off.
Setpoint Alarm Reset Actions
SETPOINT ANNUNCIATORS
mode displays the corresponding setpoint annunciators
LIMITED WARRANTY
mode disables display setpoint annunciators. The
OFF
ON
mode flashes the corresponding
nor
Building 13, No.99 Tianzhou Road
OFF
ShangHai, P.R. China 200223
Fax [phone]
mode
Tel [phone]
rEv
Unit 101, XinAn Plaza
Red Lion Controls AP
displays the
FLASH