PAXCDS40 Red Lion Controls, PAXCDS40 Datasheet - Page 4
![Quad Setpoint Sourcing Open Collector Output Interface Card](/photos/21/37/213700/4551886_sml.jpg)
PAXCDS40
Manufacturer Part Number
PAXCDS40
Description
Quad Setpoint Sourcing Open Collector Output Interface Card
Manufacturer
Red Lion Controls
Specifications of PAXCDS40
Accessory Type
Quad Setpoint Sourcing Open Collector Output Interface Card
Accuracy
± 0.01% + 10 ms
Brand/series
PAX Series
Card Type
Quad Setpoint Sourcing Open Collector Output Card
Standards
cULus Listed, CSA Certified and CE Marked
For Use With
Red Lion PAX Digital Input Panel Meters
Lead Free Status / RoHS Status
na
PAXC SPECIFICATIONS
MAXIMUM SIGNAL FREQUENCIES:
Notes:
PAXR SPECIFICATIONS
ANNUNCIATORS:
RATE DISPLAY:
FUNCTION QUESTIONS
Are any setpoints used?
Is Counter C used?
COUNT MODE
Count x1
Count x2
Quadrature x1
Quadrature x2
Quadrature x4
M
M
To determine the maximum frequency for the input(s), first answer the
questions with a yes (Y) or no (N). Next determine the Count Mode to be
used for the counter(s). If dual counters are used with different Count Modes,
then the lowest frequency applies to both counters.
1. Counter Modes are explained in the Module 1 programming section.
2. Listed values are with frequency DIP switch set on HI frequency.
SP1 - setpoint 1 output state
SP2 - setpoint 2 output state
SP3 - setpoint 3 output state
SP4 - setpoint 4 output state
Accuracy: ±0.01%
Minimum Frequency: 0.01 Hz
Maximum Frequency: 34 KHz
Maximum Display: 5 Digits: 99999
Adjustable Display (low) Update: 0.1 to 99.9 seconds
Over Range Display: “
- Rate
- Maximum (High) Rate
- Minimum (Low) Rate
ODEL
ODEL
PAXC - 1/8 DIN C
PAXR - 1/8 DIN R
Single: Counter A or B
34
17
22
17
N
N
(Values are in KHz)
8
”
25
13
19
13
N
Y
6
18
12
Y
N
9
9
4
15
10
Y
Y
7
7
3
(Values are in KHz)
Dual: Counter A & B
13
N
N
9
7
7
12
N
Y
7
6
6
N
Y
9
5
4
4
7.5
3.5
3.5
Y
Y
4
4
INPUT A:
6-DIGIT LED DISPLAY (Alternating 8 digits for counting)
DUAL COUNT QUAD INPUTS
UP TO 3 COUNT DISPLAYS
SETPOINT ALARM OUTPUTS (W/Plug-in card)
ANNUNCIATORS:
COUNTER DISPLAYS:
INPUTS A and B:
5-DIGIT LED DISPLAY
RATE INDICATION
MINIMUM/MAXIMUM RATE DISPLAYS
SETPOINT ALARM OUTPUTS (W/Plug-in card)
LOGIC: Input trigger levels V
MAGNETIC PICKUP:
A - Counter A
B - Counter B
C - Counter C
SP1 - setpoint 1 output state
SP2 - setpoint 2 output state
SP3 - setpoint 3 output state
SP4 - setpoint 4 output state
Maximum display: 8 digits: ± 99999999 (greater than 6 digits display
LOGIC: Input trigger levels V
DUAL COUNT MODES:
DIP switch selectable to accept pulses from a variety of sources including
TTL outputs, magnetic pickups and all standard RLC sensors.
Current sinking: Internal 7.8 K pull-up to +12 VDC, I
Current sourcing: Internal 3.9 K pull-down, 7.3 mA max. @ 28 VDC,
Sensitivity: 200 mV peak
Hysteresis: 100 mV
Input impedance: 3.9 K @ 60 Hz
Maximum input voltage: ±40 V peak, 30 Vrms
Alternates between high order and low order.)
DIP switch selectable to accept pulses from a variety of sources including
switch contacts, TTL outputs, magnetic pickups and all standard RLC
sensors.
Current sinking: Internal 7.8 K pull-up to +12 VDC, I
Current sourcing: Internal 3.9 K pull-down, 7.3 mA max. @ 28 VDC,
Filter: Damping capacitor provided for switch contact bounce. Limits
OUNTER
- Upper significant digit display of counter
ATE
V
V
input frequency to 50 Hz and input pulse widths to 10 msec. minimum.
When any dual count mode is used, then User Inputs 1 and/or 2 will
accept the second signal of each signal pair. The user inputs do not have
the Logic/Mag, HI/LO Freq, and Sink/Source input setup switches. The
user inputs are inherently a logic input with no low frequency filtering.
Any mechanical contacts used for these inputs in a dual count mode
must be debounced externally. The user input may only be selected for
sink/source by the User Jumper placement.
MAX
MAX
= 30 VDC.
= 30 VDC.
M
ETER
IL
IL
= 1.5 V max.; V
= 1.5 V max.; V
IH
IH
= 3.75 V min.
= 3.75 V min.
MAX
MAX
= 1.9 mA.
= 1.9 mA.