EIS-PCB NEWPORT ELECTRONICS, EIS-PCB Datasheet
EIS-PCB
Specifications of EIS-PCB
Related parts for EIS-PCB
EIS-PCB Summary of contents
Page 1
... NEWPORT Electronics, Inc. ® TM ...
Page 2
... NEWPORT Electronics, Inc. ® NEWPORT NEWPORT ® ...
Page 3
TTL RS485 ..... ........... ...
Page 4
...
Page 5
.. ...
Page 6
...
Page 7
...
Page 8
...
Page 9
TX RX RTN COMMUNICATIONS ETHERNET RESET COL DC POWER N/C ...
Page 10
OFF OFF ...
Page 11
...
Page 12
...
Page 13
... TTL RS485 Twisted shielded pair 120 Ohm Termination resistor -Tx/-Rx +Tx/+ J16A ETHERNET EIS-PCB iServer DEVICE #1 DEVICE #29 ......................... ......................... ............................... ............................... DEVICE #2 DEVICE #30 120 Ohm Termination resistor DEVICE #31 -Tx/-Rx +Tx/+Rx GND ...
Page 14
...
Page 15
...
Page 16
... OFF 3 4 http://128.100.101.254 OFF 3 4 http://eis03ec ...
Page 17
...
Page 18
...
Page 19
...
Page 20
... http://eisxxxx http://x.x.x.x x.x.x.x ...
Page 21
No. Check Device Name Device Command Response Units ...
Page 22
...
Page 23
Warranty/Disclaimer Return Requests/Inquiries ...
Page 24
...
Page 25
...
Page 26
...
Page 27
...
Page 28
...
Page 29
OFF OFF 3 4 ...
Page 30
...
Page 31
http://128.100.101.254 ...
Page 32
...
Page 33
TERMINAL SERVER reading ...
Page 34
... Firmware Version 4.0 Admin. Password:00000000 Admin. Login Successful Configuration Firmware Version 4 9600 ( none( bit ( bits ( RS-232 ( 0000 TT = SLAVE( eis1376 IP = 128.100 12345678 SP = 00000000 TP = iServer( disable( 0.0.0 02000 GW = 0.0.0 255.255.0 02000 FC = none ( disable( TCP ( not used( 01000 FE = enable ( disable( 1234abcd WB = enable (1) MAC = 00:03:34:00:13:76 ...
Page 35
Admin. Password:00000000 Admin. Login Successful iServer Configuration Command: s -[cc]pppppp [-[cc]ppppp].. cc description pppppp BD BaudRate 0-300,1-600,2-1200,3-2400,4-4800,5-9600,6-19200, 7-38400, 8-57600, 9-115200 PT Parity 0-none,1-Odd,2-even ST StopBits 0-1bits,1-2bits DT DataBits 0-7bits,1-8bits FC FlowControl 0-none,1-XON/XOFF,2-Hardware MD Mode 0-RS232, 1-RS485 MB Modbus/TCP 0-disable, 1-enable ...
Page 36
...
Page 37
...
Page 38
...
Page 39
...
Page 40
...
Page 41
...
Page 42
...
Page 43
...
Page 44
...
Page 45
...
Page 46
...
Page 47
...
Page 48
...
Page 49
...
Page 50
...
Page 51
...
Page 52
...
Page 53
...
Page 54
Category I are measurements performed on circuits not directly connected to the Mains Supply (power). Note: The ac/dc power adaptor must have Safety Qualified Agency Approvals for CE with Double Insulation rating. The ac/dc power adaptor is 9Vdc. The minimum ...
Page 55
...
Page 56
...