MPAXD000 Red Lion Controls, MPAXD000 Datasheet - Page 6

• Manufacturer Part Number: MPAXD000
• Description: Voltage-Current Input Module
• Manufacturer: Red Lion Controls

Specifications of MPAXD000

• Accessory Type: Analog Input Module
• Signal Input Type: Selectable Voltage
• No. Of Analog Outputs: 5
• Character Size: 0.56"
• Accuracy: 0.03% of reading + 0.03 μA to 0.5% of reading + 0.3 μA @ 18 to 28 °C, 0.03% of reading +30 μV to 0.05% of reading +30 mV @ 18 to 28 °C, 0.05% of reading +30 Megohm to 0.05% of reading +1 Ohms @ 18 to 28 °C
• Brand/series: MPAX Series
• Display Type: LED
• Impedance, Input: 100 Ohms to 10 Kiloohms
• Measuring Range: ± 200 μADC to ± 2 ADC, ± 200 mVDC to ± 300 VDC, 100 Ohms to 10 Kiloohms
• Resolution: 10 nA to 0.1 mA, 10 μV to 10 mV, 0.01 Ohms to 1 Ohms
• Standards: cULus Listed, CE Certified
• Voltage, Working: 85 to 250 VAC
• Sealing: NEMA 4/IP65
• No. Of Analog Inputs: 5
• Rohs Compliant: Yes
• For Use With: EPAX 5 Digit Displays
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NEMA 4/IP65 LARGE DISPLAY ENCLOSURE & SHROUD FOR EPAX
DIMENSIONS In inches (mm)
TYPICAL INSTALLATIONS FOR NEMA 4/IP65 ENCLOSURE
Picture includes the EPAX, Nema Enclosure, and Shroud
BASEMOUNT WITH WATERTIGHT
CABLE CONNECTOR ENTERING
THROUGH REAR PANEL.
*
Housing Only
service. Either the rear panel or housing may be drilled to accept sealed conduit
fittings, liquid-tight cable fittings or other types of wiring connectors. The
enclosure may be attached to horizontal surfaces located above or below it,
using the mounting channels provided.
Removing the rear panel of the enclosure allows access to the Display for
Figure 1
**
Overall Including Screwheads
SUSPENDED FROM CONDUIT
WITH SEALED FITTINGS.
(SHOWN WITH SHROUD).
Figure 2
6
DESCRIPTION
from dust and hose directed water, when properly installed. This light-weight
all aluminum unit utilizes welded seams and neoprene gaskets to meet NEMA
4/IP65 requirements. A textured, polyurethane coating protects against
corrosion and is scratch resistant. Figure 1 below shows the overall dimensions
of the Enclosure. The Display Enclosure with Mounting Channels weighs 9
pounds (4.1 Kg).
The NEMA 4/IP65 Large Display Enclosure is designed to protect the EPAX
LIGHT-WEIGHT ALUMINUM CONSTRUCTION
COMPLETELY SEALED FOR WASH-DOWN
MOUNTING CHANNELS FOR VERSATILE INSTALLATION
MOUNTING
bolts, two ¼-20 UNC “strut nuts”, and two ¼" washers. The
“strut nuts” can be installed anywhere in the channel by
inserting them, spring side down, into the channels, then
rotating them 90 degrees clockwise until the notches engage
with the lips of the channel. The bolts and washers provided
allow mounting to surfaces ¼" to ½" thick (6.4 to 12.7 mm).
Use longer bolts for mounting to thicker surfaces. Bolts
fabricated from materials other than steel are not recommended.
Provided with the enclosure are two ¼-20 UNC x 1" hex
BEAM MOUNT WITH SEALED
CONDUIT ENTERING FROM
RIGHT SIDE.
Figure 3