DT800020 Red Lion Controls, DT800020 Datasheet - Page 4

• Manufacturer Part Number: DT800020
• Description: Rate Counter
• Manufacturer: Red Lion Controls

Specifications of DT800020

• No. Of Digits / Alpha: 5
• Signal Input Type: Magnetic Or Logic
• Display Mode: LCD Negative Image Transmissive
• Meter Signal Input: Frequency
• Character Size: 0.6"
• Ip/nema Rating: IP65 / NEMA 4X
• Backlighting Color: Red
• Operating Temperature, Maximum: 60 °C
• Operating Temperature, Minimum: 0 °C
• Overall Size: 49.80 mm W x 32.80 mm H
• Supply Voltage, Logic: 3 V
• Backlight Power: 9-28VDC
• Counter Supply Voltage: 9-28VDC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
INSTALLATION ENVIRONMENT
maximum operating temperature and provides good air circulation.Placing
the unit near devices that generate excessive heat should be avoided. The
bezel should be cleaned only with a soft cloth and neutral soap product. Do
NOT use solvents.Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
INSTALLATION
properly installed. The units are intended to be mounted into an enclosed
panel. A sponge rubber gasket, mounting clip, two screws, and nut fasteners
are provided to install and seal the unit in the panel cut-out.
The following procedure assures proper installation:
1. Cut panel opening to specified dimensions. Remove burrs and clean panel
2. Slide the panel gasket over the rear of the unit to the back of the bezel.
3. Slide nut fastener into slot on mounting clip and then insert mounting screw
4. Install Ditak unit through panel cut-out.
5. Slide mounting clip over rear of unit until clip is against back of panel. The
6. Alternately tighten each mounting screw to ensure uniform gasket pressure.
The unit should be installed in a location that does not exceed the
The Ditak 8 meets NEMA4X/IP65 requirements for indoor use, when
opening.
through nut on both sides of mounting clip. Tip of mounting screw should
NOTproject through hole on clip.
mounting clip and Ditak housing have a latching feature to hold the unit in
place until tightened.
Note: Hold the Ditak front bezel in place when sliding the mounting clip
Visually inspect the gasket for proper seal. The gasket should be
compressed approximately 75 to 80% of its original thickness.
into position.
TROUBLESHOOTING
For further technical assistance, contact technical support at the appropriate company numbers listed.
workmanship for a period limited to two years from the date of shipment, provided the products
have been stored, handled, installed, and used under proper conditions. The Company’s liability
under this limited warranty shall extend only to the repair or replacement of a defective product, at
The Company’s option. The Company disclaims all liability for any affirmation, promise or
representation with respect to the products.
against damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
those expressly contained herein. The Customer acknowledges the disclaimers and limitations
contained herein and relies on no other warranties or affirmations.
NL - 3821 AD Amersfoort
Fax [phone]
Tel [phone]
The Company warrants the products it manufactures against defects in materials and
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC
No warranties expressed or implied are created with respect to The Company’s products except
Red Lion Controls
Printerweg 10
Europe
LIMITED WARRANTY
4
Ahmedabad-382480 Gujarat, India
7. If the gasket is not adequately compressed and the mounting screws cannot
8. Repeat step #6 for tightening the mounting screws.
Fax [phone]
GST Road, New Ranip,
Tel [phone]
54, Vishvas Tenement
be tightened any further, loosen mounting screws and insure that the clip is
latched as close as possible to the panel.
Red Lion Controls
LATCHING
FEATURE
MOUNTING
(1.3 TO 5.1mm)
0.05" TO 0.20"
SCREW
India
EXISTING
PANEL
THICK
FASTENER
NUT
(2.4 mm)
GASKET
0.093"
THICK
Building 13, No.99 Tianzhou Road
MOUNTING
CLIP
ShangHai, P.R. China 200223
Fax [phone]
LATCHING
Tel [phone]
FEATURE
Unit 101, XinAn Plaza
BEZEL
Red Lion Controls
China