PAXD0010 Red Lion Controls, PAXD0010 Datasheet - Page 23

• Manufacturer Part Number: PAXD0010
• Description: Multifunction Meter
• Manufacturer: Red Lion Controls
• Type: Electronicr

Specifications of PAXD0010

• No. Of Digits / Alpha: 5
• Meter Range: ± 200uA To ± 2A / ± 200mV To ± 300V / 100ohm To 10kohm
• Digit Height: 14.2mm
• Power Consumption: 11W
• Operating Temperature Range: 0°C To +50°C
• Accuracy: 0.12% of Reading +3 μA/0.12% of Reading +3 mV
• Brand/series: PAX
• Character Height: 0.56 in.
• Connection Type: Cage-Clamp
• Cut Out, Panel: 1⁄8 DIN
• Dimensions: 4.2" L × 3.8" W × 1.95" H
• Display Digit Height: 0.56 "
• Display Resolution: 10 nA to 0.1 mA/10 μV to 10 mV
• Display Type: LED
• Function: Ammeter/Voltage
• Input Type: DC Volt/Current Input
• Number Of Digits: 5
• Range, Measurement: ±200 μADC to ±2 ADC/±200 mVDC to ±300 VDC
• Temperature Range: 0 to +50 °C
• Temperature, Storage: –40 to +60 °C
• Voltage, Input: 11-36 VDV, 24 VAC
• Voltage, Supply: 11 to 36 VDC, 24 VAC
• Character Size: 0.56"
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: na

"
"
"
performed by qualified technicians using appropriate equipment. Calibration
does not change any user programmed parameters. However, it may affect the
accuracy of the input signal values previously stored using the Apply (
Scaling Style.
exiting Module 9. In this case, the existing calibration settings remain in effect.
calibrated. Also verify that the precision signal source is connected and ready.
Allow a 30 minute warm-up period before calibrating the meter.
can be chosen to exit the calibration mode without any changes taking place.
1. Use the arrow keys to display
2. Choose the range to be calibrated by using the arrow keys and press PAR.
3. When the zero range limit appears on the display, apply the appropriate:
4. Press PAR and
5. When the top range limit appears on the display, apply the appropriate:
6. Press PAR and
7. When
8. If the meter is not field scaled, then the input display should match the value
9. Repeat the above procedure for each input range to be calibrated.
5.9 MODULE 9 - F
?8,&1
PAXD - Input Calibration
(5?&
(5?&
When recalibration is required (generally every 2 years), it should only be
Calibration may be aborted by disconnecting power to the meter before
Before starting, verify that the Input Ranger Jumper is set for the range to be
Then perform the following procedure:
- Voltage ranges: dead short applied
- Current ranges: open circuit
- Resistance ranges: dead short with current source connected
- Voltage ranges: top range value applied (The 300 V range is the exception.
- Current ranges: top range value
- Resistance ranges: top range value (The ohms calibration requires
of the input signal.
It is calibrated with a 100 V signal.)
connection of the internal current source through a resistance substitution
device and the proper voltage range selection.)
WARNING: Calibration of this meter requires a signal source with an
;5
accuracy of 0.01% or better and an external meter with an accuracy
of 0.005% or better. Resistance inputs require a resistance
substitution device with an accuracy of 0.01% or better.
%%
HN
appears, press PAR twice.
#
#
#
0
RESTORE FACTORY DEFAULTS
8888
8888
using the arrow keys. The display will actively dim or
brighten as the levels are changed. This parameter also
appears in Quick Programming Mode when enabled.
The meter will display
Press DSP key to return to Display Mode. This will
overwrite all user settings with the factory settings.
DISPLAY INTENSITY LEVEL
Scaling to convert the input signal to a desired display
value is performed in Module 1. If the meter appears to be
indicating
Troubleshooting before attempting to calibrate the meter.
Enter the desired Display Intensity Level (0-15) by
Use the arrow keys to display
The meter has been fully calibrated at the factory.
will appear on the display for about 10 seconds.
will appear on the display for about 10 seconds.
CALIBRATION
(5?& HN
incorrectly
and press PAR.
#&:&6
or
ACTORY
and then return to
(5?& %%
inaccurately,
PARAMETER MENU
and press PAR.
;5
(5?& !-
S
refer
and PAR
ERVICE
"+,C
to
)
.
23
correct terminals and ready. Allow a 30 minute warm-up period before
calibrating the meter.
without any changes taking place.
1. Use the arrow keys to display
2. Choose the range to be calibrated by using the arrow keys and press PAR.
3. When the zero range limit appears on the display, apply the appropriate:
4. Press PAR and
5. When the top range limit appears on the display, apply the appropriate:
6. Press PAR and
7. When
8. If the meter is not field scaled, then the input display should match the value
9. Repeat the above procedure for each input range to be calibrated.
range to be calibrated and the Couple jumper is installed for DC. Also verify the
DC signal source is connected and ready. Allow a 30 minute warm-up period
before calibrating the meter.
mode without any changes taking place.
1. Press the arrow keys to display
2. The meter displays
3. Apply the signal matching the meter prompt.
4. Press PAR and
5. Repeat steps 3 and 4 for the remaining three prompts.
6. When
7. If the meter is scaled to show input signal, the Input Display should match
8. Repeat the above procedure for each range to be calibrated or to recalibrate
9. When all desired calibrations are completed, remove the external signal
PAXP - Input Calibration
PAXH - Input Calibration
Before starting, verify that the precision signal source is connected to the
Then perform the following procedure:
(
taking place.)
- Voltage range: dead short applied
- Current range: open circuit
- Voltage range: 10 VDC
- Current range: 20 mADC
of the input signal.
Before starting, verify the Input Range and Signal Jumpers are set for the
Then perform the following procedure:
the Signal Jumper setting. Press PAR.
the value of the input signal in the Display Mode.
the same range. It is only necessary to calibrate the input ranges being used.
source and restore original configuration and jumper settings. If AC is being
measured, continue with AC Couple Offset Calibration.
;5
O
1. +1% of full scale, DC
2. -1% of full scale, DC
3. +100% of full scale, DC; (300 V range = +100 V calibration)
4. -100% of full scale, DC; (300 V range = -100 V calibration)
and PAR can be chosen to exit the calibration mode without any changes
WARNING: In the PAXH, DC signals are used to calibrate the AC
PERATIONS
WARNING: Calibration of this meter requires a signal source with an
;5
$)
ranges. Calibration of the PAXH requires a DC voltmeter with an
accuracy of 0.025% and a precision DC signal source capable of:
accuracy of 0.01% or better and an external meter with an accuracy
of 0.005% or better.
appears, press PAR twice.
appears, press PAR twice.
8888
8888
88888
(",
;5
will appear on the display for about 10 seconds.
will appear on the display for about 10 seconds.
will appear on the display, wait for next prompt.
. Use the arrow keys to select the range that matches
and PAR can be chosen to exit the calibration mode
;5
and PAR can be chosen to exit the calibration
(5?& HN
(5?& HN
(
="236
and press PAR.
and press PAR.
)