CUB7TVSO Red Lion Controls, CUB7TVSO Datasheet
CUB7TVSO
Manufacturer Part Number
CUB7TVSO
Description
ELECTRONIC TIMER, VOLTAGE, LCD
Manufacturer
Red Lion Controls
Specifications of CUB7TVSO
Supply Voltage Range
9VDC To 28VDC
External Depth
40mm
External Length / Height
28mm
External Width
51mm
Supply Voltage Dc Max
300V
Supply Voltage Dc Min
10V
Digit Height
8.9mm
No. Of Digits /
RoHS Compliant
No. Of Digits / Alpha
8
Operating Temperature Range
0°C To +50°C
Rohs Compliant
Yes
Supply Voltage Ac Max
300V
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MODEL CUB7T1 PROGRAMMABLE GENERAL PURPOSE ELECTRONIC TIMER
DESCRIPTION
inch (8.90 mm) high digits. It has an LCD read-out available in Positive Image
Reflective (CUB7T100), Negative Image Transmissive with yellow/green
backlighting (CUB7T110) or red backlighting (CUB7T120). The backlight
versions require an external 9 to 28 VDC power supply. The display will wrap
around from a full display of “99999999” to “00000000” when an overflow
occurs. An annunciator, located in the upper left hand corner of the display,
blinks at 2 Hz when the signal input is activated. The Voltage versions
(CUB7T1xxx) operate from a signal voltage of 10 to 300 V (AC 50/60 Hz or
DC).
substrate, that is electrically connected by ultrasonic wire-bonding. Proven
micro-electronic assembly and manufacturing techniques provide these units
with the reliability and dependability required for industrial service.
a clear viewing window. The sealed front panel with the silicone rubber
buttons meets NEMA 4X/IP65 specifications for wash-down and/or dusty
environments, when properly installed.
SAFETY SUMMARY
bulletin or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
DIMENSIONS In inches (mm)
The CUB7T1 is an 8-digit miniature programmable timer with large 0.35
The CUB7T timers use a CMOS LSI chip, mounted on a gold-plated
The CUB7T series is housed in a lightweight, high impact plastic case with
All safety related regulations, local codes and instructions that appear in the
instructions prior to installation
and operation of the unit.
CAUTION: Read complete
CAUTION: Risk of electric shock.
Note: Recommended minimum clearance (behind the panel) for mounting clip installation is
2.1" (53.4) H x 5.5" (140) W.
1
SPECIFICATIONS
1. DISPLAY: 8-digit LCD, 0.35" (8.90 mm) high digits.
2. POWER SOURCE: Replaceable Internal 3.0 V lithium battery to provide up
3. BACKLIGHT POWER REQUIREMENTS: 9 to 28 VDC; 35 mA. typical,
4. ANNUNCIATOR: Annunciator in the upper left corner of the display flashes
5. SIGNAL INPUT: (LS terminal #4)
6. REMOTE RESET: 15 msec min. pulse width (active low) from 3.0 V
7. ACCURACY: 0.025% (+ up to 30 msec per activation of signal input—
8. ENVIRONMENTAL CONDITIONS:
9. CERTIFICATIONS AND COMPLIANCES:
to 6 years of continuous operation. (Battery life is dependent upon usage.
Contacts that remain closed for long periods of time reduce battery life.)
50 mA max. Above 26 VDC, derate max. operating temperature to 40°C.
at a 2 Hz rate when the signal input is activated.
Voltage Input (CUB7T1xx): 10 V min. to 300 V max. (AC 50/60 Hz. or DC)
bipolar output, an open collector transistor, or a switch contact to common.
CUB7T1xx only)
Operating Temperature Range: 0 to 50°C Derate max. operating
Storage Temperature: -30 to 80°C
Operating and Storage Humidity: 85% max. relative humidity (non-
Vibration According to IEC 68-2-6: Operational 5 to 500 Hz, in X, Y, Z
Shock According to IEC 68-2-27: Operational 30 g, 11 msec in 3 directions.
Altitude: Up to 2000 meters
SAFETY
Transmissive, Yellow/Green Transmissive) with “Timer Active”
annunciator
years of uninterrupted operation)
INDIVIDUALLY ENABLED
10 PROGRAMMABLE TIMER RANGES
3 (8 Digit 0.35") LCD DISPLAY OPTIONS (Reflective, Red
REPLACEABLE INTERNAL LITHIUM BATTERY (provides up to 6
BOTH FRONT PANEL PROGRAM AND RESET BUTTONS ARE
WIRE CONNECTIONS VIA SCREW CLAMP TYPE TERMINALS
FRONT PANEL AND REMOTE RESET INPUT
NEMA 4X/IP65 SEALED FRONT BEZEL
to Common. 150 V max. for backlight versions. Input current 0.5 mA max.
ANY off-state leakage current may activate the timer. Constant voltage
applied to the input will actuate the timer. Due to the internal digital
filtering to this input, up to 30 msec of error may be added per activation
of the signal input.
temperature to 40°C above 26 VDC (Backlight versions).
condensing) from 0°C to 50°C.
direction for 1.5 hours, 5 g’s.
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
IP65 Enclosure rating (Face only), IEC 529
Type 4X Enclosure rating (Face only).
for measurement, control, and laboratory use, Part 1.
PANEL CUT-OUT
Bulletin No. CUB7T1-J
Drawing No. LP0414
Released 2/08
Related parts for CUB7TVSO
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Counter
Manufacturer:
Red Lion Controls
Datasheet:
Part Number:
Description:
Miniature Length Sensor
Manufacturer:
Red Lion Controls
Datasheet:
Part Number:
Description:
Model Lsc - Single Channel Output Length Sensor
Manufacturer:
Red Lion Controls
Datasheet:
CUB7TVSO Summary of contents
Page 1
Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL CUB7T1 PROGRAMMABLE GENERAL PURPOSE ELECTRONIC TIMER DESCRIPTION The CUB7T1 is an 8-digit miniature programmable timer with large 0.35 inch (8.90 mm) high digits. It has an LCD read-out available in ...
Page 2
ELECTROMAGNETIC COMPATIBILITY Immunity to EN 50082-2 Electrostatic discharge EN 61000-4-2 Electromagnetic RF fields EN 61000-4-3 Fast transients (burst) EN 61000-4-4 RF conducted interference EN 61000-4-6 Simulation of cordless telephone ENV 50204 Emissions to EN 50081-1 RF interference EN 55022 Notes ...
Page 3
BATTERY INSTALLATION 1. Remove all power to the unit before removing battery cover remove the battery cover, push upward in the direction of the arrow on the rear cover (See drawing at right), until the cover unlatches. Pull ...
Page 4
RESET AND PROGRAM OPTIONS Connecting a wire from the RST EN (Reset Enable) or the HS (Program Enable) Input terminals to Common will enable the front panel Reset or Program buttons respectively. Pulling the “RST.” input low causes the timer ...