G4D32RS OPTO 22, G4D32RS Datasheet
G4D32RS
Specifications of G4D32RS
Related parts for G4D32RS
G4D32RS Summary of contents
Page 1
... DATA SHEET Form 700-030613 Description The G4D32RS is a low-cost, high-I/O-capacity digital unit for the Opto 22 family of PC-based control products. Each I/O unit offers flexible, single-point, on/off control and latching for digital I/O points. An easily accessible mounting rack makes field wiring simple to install. ...
Page 2
... Clear output Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800)TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • E-mail: sales@opto22.com ...
Page 3
... DATA SHEET Form 700-030613 Assembly The G4D32RS is a high-I/O-capacity digital unit for the Mistic family of PC-based control products. Each unit offers single-point on/off control and latching for digital I/O points. FIGURE 1: EXPLODED VIEW OF THE G4D32RS Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...
Page 4
... DATA SHEET Form 700-030613 Installation Notes Dimensions Packing List When removing the G4D32RS from its packaging, make sure the following components are included: Component • Extra jumpers • Screwdriver • G4STRAP product insert Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...
Page 5
... The following sections describe each jumper in detail. Baud Jumpers (BAUD 0-3) Use these jumpers to set the baud rate for the G4D32RS. Select the appropriate jumper settings based on the baud rates in Table 1. The I/O unit is shipped with a factory default baud rate of 115.2 KBd. ...
Page 6
... Use this jumper to select whether the type of data verification method used is Checksum Modulo 256 (jumper out) or CRC16 (jumper in, the default). CRC16 is typically used when a Mistic controller and Cyrano are used to control the G4D32RS brain boards. If you are using the MisticWARE driver or are sending commands directly from the brain boards, either data verification method may be used. ...
Page 7
... Installation Notes: Mounting the G4D32RS 1. Remove the four top cover screws and lift off the top cover. 2. Affix the G4D32RS to an enclosure or panel, using the mounting standoffs shown in Figure 4. FIGURE 4: G4D32RS DIMENSIONS AND MOUNTING INFORMATION 3. Connect power, field, and communication wiring. Refer to the appropriate sections in this document for instructions. ...
Page 8
... DATA SHEET Form 700-030613 Installation Notes: Connecting Power to the G4D32RS (cont.) G4REG The onboard regulator (Opto 22 P/N G4REG) converts the 24 VDC to the 5 VDC required by the I/O unit’s brain board and modules. Three LED indicators are on the regulator. A lit “24V” LED indicates the G4REG is receiving adequate 24 VDC power; ...
Page 9
... Several field terminals may be bussed together by using Opto 22 P/N G4STRAP. One G4STRAP may jumper positions. It may also be trimmed to jumper fewer points together. See Figure 7 for an example of how the G4STRAP is used on the G4D32RS. Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...
Page 10
... Table 2: Channel Positions and Field Terminals Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • Product Support: (800)TEK-OPTO • (951) 695-3080 • Fax: (951) 695-3017 • E-mail: sales@opto22.com ...
Page 11
... FIGURE 8: TWO-WIRE COMMUNICATION WIRING TO THE G4D32RS I/O UNIT Programming The G4D32RS may be controlled directly from with a Mistic controller and the Cyrano programming language. Refer to the Analog and Digital Commands Manual (Opto 22 form 270) or the MisticWARE Driver Reference Manual (Opto 22 form 522) for programming information if you are using control the I/O unit. Refer to the Cyrano User’ ...
Page 12
... DATA SHEET Form 700-030613 Installation Notes: LED Indicators Three LEDs are located on the G4D32RS brain board. These LEDs perform the functions described in Table 3. Table 3: LED Functions LED This indicator shows brain board status. When the brain board is RUN functioning normally, the light stays on. When the brain board is (Brain board powered down, the light goes off ...
Page 13
... Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Phone: (951) 695-3000 • (800) 321-OPTO • Fax: (951) 695-3095 • www.opto22.com Inside Sales: (800) 321-OPTO • ...