SS-39200-011 Stewart Connector, SS-39200-011 Datasheet
SS-39200-011
Specifications of SS-39200-011
Available stocks
Related parts for SS-39200-011
SS-39200-011 Summary of contents
Page 1
... Trim off approx. 1.75 to 2.00 inches of cable jacket Do not nick shield 2 Fold shield back over cable jacket 3 Spread apart pairs Shielded 39200 Series Assembly Instructions Individually Shielded Pair Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 BLUE END Blue on top. Green ...
Page 2
... Bel Stewart Connector 0.375” 4g Trim individual pair shields, leaving approximately 0.375 inches (3/8”) sticking out 5g 6g Here, Blu pair has incorrect alignment Brn Add ½ twist as low as possible 7g Brn pair is now in correct alignment Brn Page GREEN 4b beyond cable jacket 5b ...
Page 3
... Brn Org Leave load bar near end of pairs 11b Bring up Grn pair and trim so it fits into load bar Shielded 39200 Series Assembly Instructions Individually Shielded Pair Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 BLUE Grn pair around Blu pair, then ...
Page 4
... Slide load bar down to base of pairs 3/16” 13b Trim off wire ends at approx. 0.2 inches (3/16”) 14b 15 Gently insert assembly into housing Shielded 39200 Series Assembly Instructions Individually Shielded Pair Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 BLUE 3/16” MN390009-A1 ...
Page 5
... Bel Stewart Connector Page Close shield fingers by hand 17 Verify wires are visible through end of plug 18 Crimp contacts and shield fingers. Trim off excess shield Shielded 39200 Series Assembly Instructions Individually Shielded Pair Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 MN390009-A1 ...
Page 6
... Do not nick shield 2 Fold shield back over cable jacket 0.25 3 Wrap drain around cable ¼” (0.25”) behind end of jacket 4 Remove any inner insulating jacket Shielded 39200 Series Assembly Instructions Overall Shield Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 MN390009-A1 ...
Page 7
... Bel Stewart Connector 5g Untwist individual pairs to approximately 0.375 inches (3/8”) beyond cable jacket 6g Here, Grn pair has incorrect alignment Add ½ twist as low as possible 7g Grn pair is now in correct alignment 8g Fold Page GREEN 5b 6b Here Org Grn pair back Split Shielded 39200 Series Assembly Instructions ...
Page 8
... Leave load bar near end of pairs 11b Bring up Grn pair and trim so it fits into load bar 12b Slide load bar down to base of pairs Shielded 39200 Series Assembly Instructions Overall Shield Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 BLUE MN390009-A1 ...
Page 9
... Trim off wire ends at approx. 0.2 inches (3/16”) 14b 15 Gently insert assembly into housing 16 Close shield fingers by hand Keep drain wire entirely under fingers Shielded 39200 Series Assembly Instructions 11118 Susquehanna Trail South Glen Rock, PA 17327 BLUE 3/16” Overall Shield Cable MN390009-A1 ...
Page 10
... Bel Stewart Connector Page Verify wires are visible through end of plug 18 Crimp contacts and shield fingers 19 Trim off excess foil shield Shielded 39200 Series Assembly Instructions Overall Shield Cable 11118 Susquehanna Trail South Glen Rock, PA 17327 MN390009-A1 ...