BMP-5/5-3.3/4-D24-C Murata Power Solutions Inc, BMP-5/5-3.3/4-D24-C Datasheet - Page 3

• Manufacturer Part Number: BMP-5/5-3.3/4-D24-C
• Description: DC/DC TH 35W 24-5/3.3V XMP
• Manufacturer: Murata Power Solutions Inc
• Series: BMPr

Specifications of BMP-5/5-3.3/4-D24-C

• Product: Isolated
• Output Power: 25 W
• Input Voltage Range: 18 V to 36 V
• Input Voltage (nominal): 24 V
• Number Of Outputs: 2
• Output Voltage (channel 1): 5 V
• Output Current (channel 1): 5 A
• Output Voltage (channel 2): 3.3 V
• Output Current (channel 2): 4 A
• Isolation Voltage: 1.5 KV
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage, balanced "full-load" conditions, unless noted.
Input Voltage Range:
Overvoltage Shutdown:
Input Current:
Input Reflected Ripple Current:
Internal Input Filter Type
Reverse-Polarity Protection:
On/Off Control (Pin 5):
V
Minimum Loading Per Specification
Ripple/Noise (20MHz BW)
Line/Load Regulation
Efficiency
Trim Range +5V Output
Isolation Voltage:
Isolation Capacitance
Isolation Resistance
Temperature Coefficient
Current Limit Inception:
Short Circuit Current:
Overvoltage Protection:
Dynamic Load Response:
Switching Frequency
MTBF
D24 Models
D48 Models
D24 Models
D48 Models
Normal Operating Conditions
Standby Mode:
Source Impedance
D24 Models
D48 Models
D24 & D48 Models
OUT
5V Output
3.3V Output
Input-to-Output
Case-to-Input
Case-to-Output
5V @ 98.5% V
3.3V @ 98.5% V
5V Output
3.3V Output
5V Output
5V (50-100% load step to 3% VOUT)
3.3V (50-100% load step to 3% VOUT) 300μsec maximum
D24 Models
D48 Models
Off, OV, Thermal Shutdown
D24 & D48 Models
Accuracy
OUT
OUT
(3.3V @ 3.5A)
(5V @ 4.7A)
Dynamic Characteristics
Environmental
Output
Input
18-36 Volts (24V nominal)
36-75 Volts (48V nominal)
36.4-43.6 Volts (40V nominal)
77-85 Volts (83V nominal)
See Ordering Guide
10mA typical
<0.1Ω, no external input filtering
100mAp-p (typical)
Pi (4.5μF - 10μH - 7.5μF)
1 minute duration, 3A maximum
1 minute duration, 2A maximum
On = open or 2.6V to +15V, I
Off = 0-1.2V, I
±1% maximum
±1.5% maximum
10%
See Ordering Guide
See Ordering Guide
See Ordering Guide
±5%
1500Vdc minimum
1000Vdc minimum
1000Vdc mimimum
470pF
100MΩ
±0.02%/per°C
6-8 Amps
5-8 Amps
10 Amps average, continuous
8 Amps average, continuous
Magnetic feedback/transorb
6.8 volts
300μsec maximum
150kHz (±15kHz)
Bellcore, ground fixed, full power, +25°C
operating ambient temperature
TBC million hours
TBC million hours
www.murata-ps.com
IN
= 1.5mA max.
IN
= 1.5mA max.
It
5V and 3.3V, 2" x 3" Watt, Dual Output DC/DC Converters
These are stress ratings. Exposure of devices to greater than any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the Perfor-
mance/Functional Specifications Table is not implied or recommended.
Soldering Guidelines
Murata Power Solutions recommends the specifications below when installing these converters.
These specifications vary depending on the solder type. Exceeding these specifications may cause
damage to the product. Be cautious when there is high atmospheric humidity. We strongly recom-
mend a mild pre-bake (100° C. for 30 minutes). Your production environment may differ; therefore
please thoroughly review these guidelines with your process engineers.
For Sn/Ag/Cu based solders:
Maximum Preheat Temperature
Maximum Pot Temperature
Maximum Solder Dwell Time
For Sn/Pb based solders:
Maximum Preheat Temperature
Maximum Pot Temperature
Maximum Solder Dwell Time
Operating Temperature (Ambient):
Case Temperature:
Storage Temperature:
Dimensions
Shielding
Case Connection
Case Material
Pin Material
Weight:
Primary to Secondary Insulation Level
D24 Models
D48 Models
Input Voltage:
Input Reverse-Polarity Protection
Output Overvoltage Protection
Output Current
Storage Temperature
Without Derating:
With Derating
Maximum Operational
For Thermal Shutdown
D24 Models
D48 Models
+5V Outputs
All models are specified with no external output capacitors.
See Technical Notes/Graphs for details.
Devices may be ordered with On/Off Control function. See Part Number Suffixes and Technical Notes for details.
Applying a voltage to On/Off Control (pin 5) when no input power is applied to the converter may cause perma-
nent damage.
Output noise may be further reduced with the installation of additional external output capacitors.
On/Off control is designed to be driven with open collector or by appropriate voltage levels. Voltages must be
referenced to the input return pin (–Input).
Demonstrated MTBF available on request.
Wave Solder Operations for through-hole mounted products (THMT)
Technical enquiries email: [e-mail], tel:
Absolute Maximum Ratings
Environmental, continued
Physical
No heat sink
–40 to +50°C
To +100°C (See Derating Curves)
+100°C
+95°C minimum, +105°C maximum
–40 to +120°C
2.04 x 3.04 x 0.55" (51.8 x 77.2 x 14mm)
5-sided
Pin 4
Aluminum, black anodized finish with
plastic header
Gold-plated copper alloy with nickel underplate
6 ounces (170 grams)
Operational
Basic
42 Volts
88 Volts
Current must be <3A. Brief duration
only. Fusing recommended.
6.8 Volts
Current limited. Maximum current
and short-circuit duration are model
dependent.
–40 to +105°C
115° C.
270° C.
7 seconds
105° C.
250° C.
6 seconds
BMP Models
MDC_BMP-5.5.B01 Page 3 of 5
[phone]