CUB5IR00 Red Lion Controls, CUB5IR00 Datasheet - Page 6

• Manufacturer Part Number: CUB5IR00
• Description: DC Current Meter With Reflective Display
• Manufacturer: Red Lion Controls
• Type: Currentr

Specifications of CUB5IR00

• No. Of Digits / Alpha: 5
• Digit Height: 12.2mm
• Supply Voltage Range: 9VDC To 28VDC
• Operating Temperature Range: -35°C To +75°C
• External Depth: 43.4mm
• External Length / Height: 39.1mm
• External: RoHS Compliant
• Accuracy: ±0.01% %
• Connection Type: Screw
• Cut Out, Panel: 2.68×1.3 "
• Dimensions: 2.95"L×1.86"W×1.54"H
• Display Digit Height: 0.48 "
• Display Type: LCD
• Function: Current
• Material, Casing: Plastic
• Number Of Digits: 5
• Primary Type: Electronic
• Range, Measurement: 200 μA to 200 mA
• Special Features: Communication and Control
• Voltage, Supply: 9 to 28 VDC
• Power Supply: 9 to 28 VDC
• Dc Current: 200 μA to 200 mA
• Dc Voltage: 200 mV to 200 V
• Process Signals: 0(4) to 20 mA or 0 - 10 VDC

OPERATING MODE DISPLAY DESIGNATORS
the enabled display values.
PROGRAMMING MODE ENTRY (SEL BUTTON)
installation. The meter normally operates in the Display Mode. No parameters
can be programmed in this mode. The Programming Mode is entered by
pressing and holding the
either a security code, or a hardware lock.
MODULE ENTRY (SEL & RST BUTTONS)
group together parameters that are related in function. The display will alternate
between
module. The displayed module is entered by pressing the
MODULE MENU (SEL BUTTON)
module discussion). The
parameter to be changed, without changing the programming of preceding
parameters. After completing a module, the display will return to
Programming may continue by accessing additional modules.
SELECTION / VALUE ENTRY
the selections/value for that parameter. The
the selections/values for that parameter. Pressing the
activates the displayed selection/value. This also advances the meter to the next
parameter.
most digit will begin to flash. Pressing the
digit by one or the user can hold the
scroll. The
SEL
5.0 R
6.0 P
MAX - Maximum display capture value
MIN - Minimum display capture value
Pressing the
It is recommended all programming changes be made off line, or before
The Programming Menu is organized into separate modules. These modules
Each module has a separate module menu (which is shown at the start of each
For each parameter, the display alternates between the present parameter and
For numeric values, press the
button will enter the value and move to the next parameter.
BUTTON
Pro
RST
SEL
SEL
and the present module. The
SEL
button will advance to the next digit. Pressing and holding the
ROGRAMMING THE
EVIEWING THE
button toggles the meter through the selected displays. If display scroll is enabled, the display will toggle automatically every four seconds between
DISPLAY MODE OPERATION
Index display through enabled values
Resets values (MIN/MAX) or outputs
SEL
SEL
button. If it is not accessible then it is locked by
button is pressed to advance to a particular
RST
RST
button to access the value. The right hand
RST
button and the digit will automatically
RST
button is used to select the desired
RST
button is used to move through
button again increments the
SEL
SEL
button, stores and
button.
PROGRAMMING MENU
ENTERING PROGRAM MODE
Press and hold for 2 seconds to activate
F
Pro
RONT
OVERVIEW
NO
M
.
6
ETER
PROGRAMMING MODE EXIT (SEL BUTTON)
displayed. This will commit any stored parameter changes to memory and
return the meter to the Display Mode. (If power loss occurs before returning to
the Display Mode, verify recent parameter changes.)
PROGRAMMING TIPS
sequence. When programming is complete, it is recommended to record the
parameter programming and lock out parameter programming with the user input
or programming security code.
FACTORY SETTINGS
when encountering programming problems.
ALTERNATING SELECTION DISPLAY
appear. This is used to illustrate the display alternating between the parameter
on top and the parameter’s Factory Setting on the bottom. In most cases,
selections and values for the parameter will be listed on the right.
“1” - To the right of the display indicates setpoint 1 output activated.
“2” - To the right of the display indicates setpoint 2 output activated.
The Programming Mode is exited by pressing the
It is recommended to start with Module 1 and proceed through each module in
Factory Settings may be completely restored in Module 2. This is useful
In the explanation of the modules, the following dual display with arrows will
B
UTTONS AND
Parameter
Indicates Program Mode Alternating Display
PROGRAMMING MODE OPERATION
Store selected parameter and index to next parameter
Advances through the program menu
Increments selected parameter value or selection
Factory Settings are shown.
USrIN
N0
D
Selection/Value
ISPLAY
SEL
button with
Pro NO