P4810107 Red Lion Controls, P4810107 Datasheet - Page 2

no-image

P4810107

Manufacturer Part Number
P4810107
Description
PRC CNTL,ANL,01R,A2R,485
Manufacturer
Red Lion Controls
Datasheet

Specifications of P4810107

Rohs Compliant
NA
SAFETY SUMMARY
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
equipped with safeguards. To do so can be potentially harmful to persons or
equipment in the event of a fault to the controller. An independent and redundant
process limit indicator with alarm outputs is strongly recommended.
SPECIFICATIONS
1. DISPLAY: Dual 4-digit
2. POWER:
3. CONTROLS: Four front panel push buttons for modification and setup of
4. MEMORY: Nonvolatile E
5. RANGE AND ACCURACY:
6. MAIN SIGNAL INPUT:
7. USER INPUT: Internally pulled up to +5 VDC (1 M).
8. CONTROL AND ALARM OUTPUTS:
All safety related regulations, local codes and instructions that appear in the
Do not use the P48 to directly command motors, valves, or other actuators not
Upper Process Display: 0.4" (10.2 mm) high red LED
Lower Auxiliary Display: 0.3" (7.6 mm) high green LED
Display Messages:
LED Status Annunciators:
AC Versions: 85 VAC min. to 250 VAC max., 50 to 60 Hz, 8 VA max.
DC Versions:
controller functions and one external user input for parameter lockout or other
functions.
and values.
* Accuracies are expressed as percentages after 20 minutes warm-up. The
Sample Period: 100 msec
Response Time: Less than 300 msec typ., 400 msec max. (to within 99% of
Normal Mode Rejection: 40 dB @ 50/60 Hz (improves with increased
Common Mode Rejection: Greater than 120 dB, DC to 60 Hz
Protection: Input overload 120 VAC max. for 15 sec. max.
V
I
Response Time: 120 msec max.
Functions:
Relay outputs with Form A contacts:
20 mA DC
OFF
(-2 to 22)
(-1 to 11)
IN MAX
10 VDC
RANGE
“OLOL”
“ULUL”
“SENS”
“...”
“-..”
%P
MN
DV
O1
A1
A2
DC Power: 18 to 36 VDC; 7 W
AC Power: 24 VAC 10%; 50 to 60 Hz, 9 VA
controller’s accuracy is specified in two ways: accuracy over an 18 to 28°C
range at 10 to 75% RH environment; and accuracy over a 0 to 50°C range
at 0 to 85% RH (non-condensing) environment. Accuracy over the wide
sensor range reflects the coefficient of the internal circuitry.
final value w/step input; typically, response is limited to response time of
sensor)
digital filtering.)
Contact Rating: 3 A @ 250 VAC or 30 VDC (resistive load)
Life Expectancy: 100,000 cycles at max. load rating.
INPUT
= 1μA max.
1/10 HP @ 120 VAC (inductive load)
(Decreasing load and/or increasing cycle time, increases life
expectancy.)
= 5.25 VDC; V
ACCURACY *
(18 to 28°C)
- Appears when measurement exceeds + input range.
- Appears when measurement exceeds - input range.
- Appears when measurement exceeds controller limits.
- Appears when display values exceed + display range.
- Appears when display values exceed - display range.
- Lower auxiliary display shows power output in (%).
- Flashing: Controller is in manual mode.
- Lower auxiliary display shows deviation (error) from
- Main control output is active.
- Alarm #1 is active (for A1 option).
- Alarm #2 is active OR
- Secondary output (02) is active.
+0.03 mA
0.10% of
0.10% of
+0.02 V
reading
reading
setpoint.
Program Lock
Auto/Manual Mode Select
Reset Alarms
Local/Remote Setpoint Select
On: Local Setpoint (Remote Setpoint option)
Off: Remote Setpoint
ACCURACY *
IL
(0 to 50°C)
+0.04 mA
0.30% of
0.30% of
+0.03 V
reading
reading
= 0.85 V max.; V
2
PROM retains all programmable parameters
IMPEDANCE
1 M ohm
10 ohm
IH
= 3.65 V min.;
Integral Action Lock
Setpoint Ramp Enable
Setpoint 1/Setpoint 2 Select
Serial block print
CONTINUOUS
OVERLOAD
100 mA
300 V
MAX
RESOLUTION
10 mV
10 μA
2
9. MAIN CONTROL:
10. ALARMS: 1 or 2 alarms (optional)
11. SECONDARY OUTPUT: Software selectable (overrides alarm 2)
12. MAIN AND SECOND LINEAR DC OUTPUT: (optional)
* Accuracies are expressed as percentages after 20 minutes warm-up. Output
** Outputs are independently jumper selectable for either 10 V or 20 mA. The
13. REMOTE SETPOINT INPUT: (optional)
14. SERIAL COMMUNICATIONS: (optional)
15. ENVIRONMENTAL CONDITIONS:
Control: PID or ON/OFF
Output: Time proportioning or Linear DC
Cycle time: Programmable
Auto-tune: When selected, sets proportional band, integral time, and
Modes:
Reset Action: Programmable; automatic or latched
Standby Mode: Programmable; enable or disable
Hysteresis: Programmable
Annunciator: LED backlight for “A1”, “A2”
Control: PID or ON/OFF
Output: Time Proportioning
Cycle time: Programmable
Proportional Gain Adjust: Programmable
Deadband /Overlap: Programmable
Main: Control or re-transmission, programmable update rate from 0.1 sec to
Second: Re-transmission only, fixed update rate of 0.1 sec
accuracy is specified in two ways: Accuracy over an 18 to 28°C range at 10
to 75% RH environment; and accuracy over a 0 to 50°C range at 0 to 85%
RH (non-condensing) environment. Accuracy over the wide sensor range
reflects the coeffecient of the internal circuitry.
output range may be field calibrated to yield approximately 10% overrange
and a small underrange (negative) signal.
Input type: 0/4 to 20 mA
Input Resistance: 10
Overrange: -5% to 105%
Overload: 100 mA (continuous)
Scale Range: -999 to 9999
Resolution: 1 part in 10,000.
Accuracy:
Reading Rate: 10/sec.
Setpoint Filtering: Programmable Digital
Setpoint Ramping: Programmable, 1 to 9999 units/minute.
Type: RS485 multipoint, balanced interface
Baud Rate: 300 to 9600
Data Format: 7O1, 7E1, 7N2, 8N1
Node Address: 0 to 99, max of 32 units per line
Transmit Delay: 2 to 100 msec or 100 to 200 msec
Data Encoding: ASCII
Isolation w.r.t Main Input Common: 500 Vrms for 1 min. (50 V working)
Note: RS485 and the Analog Output commons are not internally isolated
Operating Range: 0 to 50°C
Storage Range: -40 to 80°C
Operating and Storage Humidity:
Vibration According to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z
Shock According to IEC 68-2-27: Operational 20 g (10 g relay), 11 msec
Altitude: Up to 2000 meters
0 to 20 mA
4 to 20 mA
derivative time values.
250 sec
OUTPUT **
At 25
Over 0 to 50
within the controller. The terminating equipment of these outputs must not
share the same common (ie. earth ground).
85% max. relative humidity (non-condensing) from 0°C to 50°C.
direction for 1.5 hours, 2 g.
in 3 directions.
0 to 10 V
RANGE
Not isolated w.r.t. Remote Setpoint or Analog Output common
°
C:
Absolute high acting
Deviation high acting
Inside band acting
(0.1 % of full scale +
°
0.10% of FS
0.10% of FS
0.10% of FS
ACCURACY *
C range:
(18 to 28°C)
+ 1/2 LSD
+ 1/2 LSD
+ 1/2 LSD
(0.2% of full scale +
ACCURACY *
0.30% of FS
0.30% of FS
0.30% of FS
+ 1/2 LSD
+ 1/2 LSD
+ 1/2 LSD
(0 to 50°C)
½
LSD)
Absolute low acting
Deviation low acting
Outside band acting
500 ohm max.
500 ohm max.
10k ohm min.
COMPLIANCE
½
LSD)
RESOLUTION
1/3500
1/3500
1/2800

Related parts for P4810107