T1621100 Red Lion Controls, T1621100 Datasheet - Page 3

• Manufacturer Part Number: T1621100
• Description: W/Solid State Out, 2 Alarms, And User Input
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of T1621100

• Brand/series: T16 Series
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Output Type: Digital/SSR
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE
• Termination: Screw
• Voltage, Supply: 85 to 250 VAC

INPUT SPECIFICATIONS (Cont’d)
4. SIGNAL INPUT: (P16 only)
OUTPUT SPECIFICATIONS
1. CONTROL AND ALARM OUTPUTS:
2. MAIN CONTROL:
3. ALARMS: (optional) 2 relay alarm outputs.
ORDERING INFORMATION
* Analog out may be used for retransmitted signals. When using analog output for retransmitted signals,
AL1 becomes main control O1, if selected for heating in the analog out models.
* Accuracies are expressed as ± percentages over 0 to 50 °C ambient range
Relay Output:
Type: Form A
Contact Rating: 3 A @ 250 VAC or 30 VDC; 1/10 HP @ 120 VAC
Life Expectancy: 100,000 cycles at max. load rating
Logic/SSR Output (main control output only):
Control: PID or On/Off
Output: Time proportioning or DC Analog
Cycle Time: Programmable
Auto-Tune: When selected, sets proportional band, integral time, derivative
Probe Break Action: Programmable
Modes:
MODEL NO.
after 20 minute warm-up.
(inductive load)
(Decreasing load and/or increasing cycle time, increases life expectancy)
Rating: 45 mA max @ 4 V min., 7 V nominal
time, and output dampening time. Also sets input filter and (if applicable)
cooling gain.
None
Absolute High Acting (Balanced or Unbalanced Hysteresis)
Absolute Low Acting (Balanced or Unbalanced Hysteresis)
Deviation High Acting
Deviation Low Acting
Inside Band Acting
Outside Band Acting
Heat (Alarm 1 on Analog Output models only)
Cool (Alarm 2)
P16
T16
ACCESSORIES
INPUT RANGE ACCURACY * IMPEDANCE
MODEL NO.
20 mA DC
(-2 to 22)
(-1 to 11)
10 VDC
TP16
RLY
MAIN CONTROL
Analog Out *
Analog Out *
DESCRIPTION
Programming Kit 1 : Includes Software, Comms Module w/
9-pin connector and cable, and 115 VAC Power Adapter
Programming Kit 2 : Includes Software, Comms Module w/
9-pin connector and cable
External SSR Power Unit (for Logic/SSR models)
25 A Single Phase Din Rail Mount Solid State Relay
40 A Single Phase Din Rail Mount Solid State Relay
Three Phase Din Rail Mount Solid State Relay
Logic/SSR
Logic/SSR
Logic/SSR
Logic/SSR
0.30 % of
0.30 % of
Relay
Relay
Relay
Relay
+0.04mA
reading
reading
+0.03V
1 MΩ
10 Ω
2 ALARMS & USER INPUT
CONTINUOUS
OVERLOAD
Yes
Yes
Yes
Yes
Yes
Yes
—
—
—
—
100 mA
50 V
MAX
RESOLUTION
10 mV
10 µA
18-36 VDC/24 VAC
T1610010
T1620010
P1610010
P1620010
P1621110
P1641110
T1611110
T1621110
T1641110
P1611110
PART NUMBERS
3
PART NUMBERS
RLY6A000
TP16KIT1
TP16KIT2
RLY50000
RLY60000
RLY70000
5. TEMPERATURE INDICATION ACCURACY: (T16 only)
6. USER INPUT: (Only controllers with alarms have a user input terminal.)
4. COOLING: Software selectable (overrides Alarm 2).
5. ANALOG DC OUTPUT: (optional)
± (0.3% of span, +1°C) at 23 °C ambient after 20 minute warm up. Includes
NIST conformity, cold junction effect, A/D conversion errors and
linearization conformity.
Span Drift (maximum): 130 PPM/°C
Internally pulled up to +7 VDC (100 KΩ), V
V
Response Time: 120 msec max
Functions: Programmable
Reset Action: Programmable; automatic or latched
Standby Mode: Programmable; enable or disable
Hysteresis: Programmable
Sensor Fail Response: Upscale
Annunciator: “A1” and “A2” programmable for normal or reverse acting
Control: PID or On/Off
Output: Time proportioning
Cycle Time: Programmable
Proportional Gain Adjust: Programmable
Heat/Cool Deadband Overlap: Programmable
Action: Control or retransmission
Update Rate: 0.1 to 250 sec
* Accuracies are expressed as ± percentages over 0 to 50 °C ambient range
** Outputs are independently jumper selectable for either 10 V or 20 mA. The
85 to 250 VAC
IH
P1610000
P1620000
T1610000
T1611100
T1620000
T1621100
T1641100
P1611100
P1621100
P1641100
0 to 20 mA
4 to 20 mA
after 20 minute warm-up.
output range may be field calibrated to yield approximately 5% overrange
and a small underrange (negative) signal.
RANGE **
0 to 10 V
OUTPUT
= 1.5 V min, I
ACCURACY *
0.3% of FS
0.3% of FS
0.3% of FS
OFF
+ ½ LSD
+ ½ LSD
+ ½ LSD
= 40 µA max
COMPLIANCE
500 Ω max
500 Ω max
10 kΩ min
IN MAX
RESOLUTION
1/8000
1/8000
1/6400
= 35 V, V
IL
= 0.6 V max,