LSN2-T/16-W3G-C Murata Power Solutions Inc, LSN2-T/16-W3G-C Datasheet
LSN2-T/16-W3G-C
Specifications of LSN2-T/16-W3G-C
Related parts for LSN2-T/16-W3G-C
LSN2-T/16-W3G-C Summary of contents
Page 1
... LSN2 converters for local 1.8 and 3.3Vdc sup- plies. All system isolation resides in the central supply, leaving lower cost POL regulation at the load. The LSN2’s can deliver very high power (to 52 Watts tiny area without heat sinking or external components. They feature quick transient response (to 25μ ...
Page 2
... Please refer to the separate LSN2-T/30 data sheet. ➂ These devices have no minimum-load requirements and will regulate under no-load conditions. Regula- tion specifi cations describe the output-voltage deviation as the line voltage or load is varied from its nominal/midpoint value to either extreme. ...
Page 3
... Power Good Output (14) (“G” suffi x) Power_Good Confi guration Dynamic Load Response (50-100-50% load step, di/dt = 20A/msec) Start-Up Time Switching Frequency LSN2-T/6 models LSN2-T/10 and -T/16 models max. IN max. IN Calculated MTBF (4) Operating Temperature Range (Ambient) No derating, natural convection With derating ...
Page 4
... Maximum Preheat Temperature Maximum Pot Temperature Maximum Solder Dwell Time For Sn/Pb based solders: Maximum Preheat Temperature Maximum Pot Temperature Maximum Solder Dwell Time www.murata-ps.com LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters ABSOLUTE MAXIMUM RATINGS +7 Volts +15 Volts –0.3V min max. ...
Page 5
... I/O Filtering and Noise Reduction All models in the LSN2 Series are tested and specifi ed with external 1 || 10μF ceramic/tantalum output capacitors and a 22μF tantalum input capacitor. These capacitors are necessary to accommodate our test equipment and may not be required to achieve desired performance in your application. The ...
Page 6
... Input Fusing Most applications and or safety agencies require the installation of fuses at the inputs of power conversion components. The LSN2 Series are not internally fused. Therefore, if input fusing is mandatory, either a normal-blow or a slow-blow fuse with a value no greater than twice the maximum input current calculated at low line with the converter's minimum effi ...
Page 7
... Power-up sequencing If a controlled start-up of one or more LSN2 Series DC/DC converters is required several output voltages need to be powered- given sequence, the On/Off control pin can be driven with an external open collector device as per Figure 4 ...
Page 8
... As you may deduce from the derating curves and observe in the effi ciency curves on the following pages, LSN2 SIPs maintain virtually constant effi cien- cy from half to full load, and consequently deliver very impressive temperature performance even if operating at full load ...
Page 9
... OUT V Open TRIM D12 Models Voltage Trim Equation: V TRIM The LSN2 D12 fi xed trim voltages to set the output voltage are: V (Typ.) 0.7525V 1.0V OUT V TRIM LSN2 Power Sequencing Whereas in the old days, one master switch simultaneously turned on the power for all parts of a system, many modern systems require multiple supply voltages for different on-board sections ...
Page 10
... Lastly, changing the timing may require reprogramming the logic sequencer or rewriting software. Sequence/Track Input A different power sequencing solution is employed on MPS’s LSN2 DC/DC converter. After external input power is applied and the converter stabilizes, a high impedance Sequence/Track input pin accepts an external analog volt- age ...
Page 11
... Any strategy may be used to deliver the power up/down ramps. The circuits Time) OUT below show simple RC networks but you may also use operational amplifi ers, D/A converters, etc. www.murata-ps.com LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2.B07Δ ...
Page 12
... And the bias current will slowly charge up any external caps over time if they are not grounded. The internal pull-up resistor to +V typically 400k: to 1M:. www.murata-ps.com LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters Figure 14. Proportional Phasing powered all during the down ramp email: sales@murata-ps ...
Page 13
... FET is at saturation, approximately +0.2V output. Keep this LOW (FALSE) pulldown current to less than 10mA. Please note that Power Good is briefl y false during Sequence ramp-up. Ignore Power Good while in transition. www.murata-ps.com LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters email: sales@murata-ps.com 25 Jun 2010 MDC_LSN2.B07Δ ...
Page 14
... Power Good output is optional. +Input If not installed, the pin is omitted. /Sequence Trim www.murata-ps.com LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters Dimensions are in inches (mm shown for ref. only). Third Angle Projection Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± ...
Page 15
... The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. www.murata-ps.com/locations LSN2 Series Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters Natural Convection ...