DIN2R-40-120-L1 SUPERIOR ELECTRIC, DIN2R-40-120-L1 Datasheet

DIN2R-40-120-L1

Manufacturer Part Number

DIN2R-40-120-L1

Description

DIN Rail Mounted Surge Suppressor

Manufacturer

SUPERIOR ELECTRIC

Series

DIN2R-40r

Type

Single-Poler

Datasheet

1.DIN2R-40-120-L1.pdf (4 pages)

Specifications of DIN2R-40-120-L1

Suppressor Type

Data Line

Voltage Rating

120VAC

Operating Voltage Range

120VAC To 240VAC

Peak Surge Current

40kA

Connector Type

Screw Terminal

Frequency Max

64Hz

Brand/series

STABILINE®/DIN2R-40 Series

Current, Surge

40 kA

Dimensions

18 W × 90 H × 67 D mm

Ip Rating

IP20

Mounting Type

DIN Rail

Primary Type

Transient Voltage Surge Suppressor

Termination

Screw

Voltage, Operating

150 V

Voltage, Supply

120, 120/240, 120/208 V

Wire Size

10-4 AWG

For Use With

Industrial Equipment

Current page: 1 of 4
Download datasheet (766Kb)

UL Recognized for USA and Canada

DIN2R-40 Series Benefits

DIN Rail mountable surge

protection devices

Replaceable SPD modules

- eliminate costly, time-consuming

- simple snap “in/out” design for

- compact, lightweight yet rugged

Visual monitor advises protection

present status

Model choices allow for single mode or

all-mode protection strategies

Each protector module / fixed base are

“keyed” to ensure proper application

All protectors (except N-G model)

equipped with signaling relay

contacts for remote monitoring of

protection status

Automatic Voltage Regulators • Power Conditioners • Uninterruptible Power Supplies

replacement wiring

rapid maintenance

Replaceable Plug-In Surge Protection Module

DIN2R-40 Series STABILINE Transient Voltage Surge Suppressors

are single pole, parallel-connected, MOV technology Class II,

Category B Surge Protective Devices suitable for use in AC elec-

trical power systems for protection against surge and transient

activity. Each protector provides 40 kA Surge Amp Capacity

protection in maintenance free, low profile, IP20 enclosure, DIN

Rail mountable module.

Installation

DIN2R-40 Protectors are installed/connected in parallel with

the line and the equipment to be protected. The DIN2R-40 unit

should be installed down stream of a 125 A maximum fuse or

breaker. If pre-existing fuses or breakers are present, then the

fusing or breaker used for the DIN2R-40 protector should have

a lower rating in order to be properly coordinated, as per ap-

plicable electrical regulatory standards. The short circuit current

rating for these DIN2R-40 protectors are 25,000 Amps using a

50A Class J time delayed fuse.

Remote Monitoring

All DIN2R-40 protectors (except N - G protector) come standard

with one remote monitoring relay with “dry Form C contacts”

per module. The contact can be used to drive several different

types of indicators such as a remote light indicator or an audible

alarm. The contact ratings are 250V RMS max, 2A max. The

connection to the remote signal is through the screw terminals.

Visual Protection Status

All DIN2R-40 protectors are maintenance free devices. If the unit

is subjected to a prolonged over-voltage condition, an internal

thermal element will activate, disconnecting the DIN2R-40 from

the line. When the unit is no longer providing protection the win-

dow on the front of the DIN2R-40 becomes red and a replace-

ment module will be required.

DIN2R-40 Series — Surge Protective Devices (SPD)

Parallel-Connected Design/Single Pole (Mode) Protectors

Related parts for DIN2R-40-120-L1

DIN2R-40-120-L1 Summary of contents

Page 1

... All DIN2R-40 protectors are maintenance free devices. If the unit is subjected to a prolonged over-voltage condition, an internal thermal element will activate, disconnecting the DIN2R-40 from the line. When the unit is no longer providing protection the win- dow on the front of the DIN2R-40 becomes red and a replace- ment module will be required. ...

Page 2

... Model Typical Service Configurations Numbers 1 ∅, 120 VAC, 2-Wire, w/ground DIN2R-40-120-L1 1 ∅, 120/240 VAC, 3-Wire SPLIT-PHASE, w/ground 3 ∅, 208Y/120 VAC, 4-Wire WYE, w/ground 1 ∅, 220 VAC, 2-Wire, w/ground DIN2R-40-220-L1 3 ∅, 380Y/220 VAC, 4-Wire WYE, w/ground 3 ∅, 220 VAC, 3-Wire DELTA 1 ∅ ...

Page 3

... Ibs (0.11 kg) L-N; L-G; L-L protectors use MOV technology and N-G protector uses Gas Tube 47-64 Hz DIN2R-40 protectors incorporate an internal thermal disconnect system with time-delayed Class J,30A-125A over current fuses Applications Control panels feeding PLCs, VSDs and other control system components ...

Page 4

... Ground Protector Telephone and Fax Numbers Telephone: 860-507-2025 Fax: 860-507-2050 Customer Service 860-507-2025, Ext 70782 Product Application 860-507-2025, Ext 72058 Printed in USA F7050 REV B 7/09 ©2009 Superior Electric 2.63 in (67 mm) .71 in (18 mm (51 mm L/N TVSS UL 1449 ed2 S A SABS IEC 61643-1 ...

Related keywords

DIN2R-40-120-L1 datasheet
DIN2R-40-120-L1 data sheet
DIN2R-40-120-L1 pdf datasheet
DIN2R-40-120-L1 component
DIN2R-40-120-L1 part
DIN2R-40-120-L1 distributor
DIN2R-40-120-L1 RoHS
DIN2R-40-120-L1 datasheet download