DLP180-24/E TDK Corporation, DLP180-24/E Datasheet
![PSU, DIN RAIL, 24V, 7.5A](/photos/21/71/217173/42270609_sml.jpg)
DLP180-24/E
Manufacturer Part Number
DLP180-24/E
Description
PSU, DIN RAIL, 24V, 7.5A
Manufacturer
TDK Corporation
Datasheet
1.DLP180-24E.pdf
(2 pages)
Specifications of DLP180-24/E
Power Supply Type
Switch Mode
Power Supply Output Type
Fixed
No. Of Output Channels
1
Input Frequency
63Hz
Output Voltage
24V
Output Current
7.5A
Power Rating
180W
Input Voltage
85VAC To 265VAC /
No. Of Outputs
1
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
CA735-01-01B
This specifications sheet also apply to option model /E,/EJ
* Read instruction manual carefully , before using the power supply unit
* 1 : At 100/230VAC and maximum output power, Ta = 25°C.
* 2 : For cases where conformance to various safety specs ( UL, CSA, EN ) are required, to be described as
* 3 : Not applicable for the in-rush current to Noise Filter for less than 0.2ms
* 4 : Please refer to Fig A for measurement of line & load regulation and output ripple voltage
* 5 : 85 - 265VAC, constant load.
* 6 : No load - Full load(Maximum power), constant input voltage
* 7 : Constant current limit with automatic recovery
* 8 : OVP circuit will shutdown output, manual reset. (Re power on)
* 9 : Measured by each measuring method of UL, CSA, EN and
*10: At standard mounting method, Fig B.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
2
3
4
5
6
7
8
9
Nominal Output Voltage
Maximum Output Current
Maximum Output Power
Efficiency
Input Voltage Range
Input Current
Inrush Current
PFHC
Power Factor (Typ)
Output Voltage Range
Maximum Ripple & Noise
Maximum Line Regulation
Maximum Load Regulation
Temperature Coefficient
Over Current Protection
Over Voltage Protection
Hold-Up Time
Leakage current
Parallel Operation
Series Operation
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Cooling
Withstand Voltage
Isolation Resistance
Vibration
Shock(In package)
Safety
EMI
Immunity
Weight (Typ)
Size ( W.H.D.)
- Load(%) is percent of maximum output load ( Item2 and 3 ), do
-For standard mounting, refer to derating curve (CA735-01-02_)
(Measure with JEITA RC-9131 probe)
100 - 240VAC, 50 / 60Hz on name plate.
Avoid to operate at overload or dead short for more than 30seconds
DENAN (at 60Hz).
ITEMS
not exceed derating in both Maximum Output Current and Power.
= NOTES=
(100/230VAC) (Typ)
(100/230VAC) (Typ)
(100/230VAC) (Typ)
( * 4 )
(100/230VAC)
-10≤Ta<0°C
0≤Ta≤60°C
( * 4, 5) mV
( * 4, 6) mV
( * 10 )
DLP180-24-1 SPECIFICATIONS
( * 1 ) %
( * 2 )
( * 1 ) A
( * 3 )
( * 1 )
( * 7 ) A
( * 8 ) V
( * 1 )
( * 9 )
MODE
mm
mV
mV
W
V
A
V
g
EN60529 IP20, EN50178 CATEGORY III(Primary), Built to meet DENAN
Approved by UL60950,CSA60950, EN60950, UL508, CSA C22.2 No14,
More than 100M Ω at Ta=25°C and 70%RH, Output - FG : 500VDC
Input - Output : 3.0kVAC, Input - FG : 2.0kVAC (20mA) for 1min
10~55Hz (Sweep for 1min) 9.8m/s
Output
terminal
Built to meet IEC61000-6-2 (IEC61000-4-2,-3,-4,-5,-6,-8,-11)
Measurement point for
Vo Line/Load Regulation.
Built to meet VCCI-B, FCC-ClassB, EN55011/EN55022-B
20A at 100VAC, 45A at 230VAC, Ta=25
Convection: -10 ~ +50°C ( 100% ); 60°C ( 60% )
85 ~ 265VAC (47-63Hz) or 120 ~ 370VDC
Output - FG : 500VAC (100mA) for 1min.
80x97x110 (Refer to Outline Drawing)
At no operating and with DIN RAIL,
+V
-V
Built to meet IEC61000-3-2
30 ~ 90 %RH (No dewdrop)
10 ~ 95%RH (No dewdrop)
Convection cooling
Less than 0.05%/°C
Less than 0.75mA
Less than 196m/s
DLP180-24-1
- 10 ~ + 60 °C
- 30 ~ +85°C
L
20ms /30ms
30.0~35.0
0.99 / 0.95
21.6~28
Possible
2.3/1.0
84/87
7.9~
180
240
360
120
192
780
7.5
24
-
2
Measurement point
for Vripple
Constant, X, Y, Z each 1hour
Output terminal
2
+
C1 C2
o
C, Cold Start
A
DENSEI-LAMBDA
C1 : Elec. Cap 100uF
C2 : Film Cap 0.1uF
Bandwidth of scope : 100MHz
L : 150mm
Input terminal
Fig. A
Rail
Fig. B
Related parts for DLP180-24/E
DLP180-24/E Summary of contents
Page 1
... Measured by each measuring method of UL, CSA, EN and DENAN (at 60Hz). *10: At standard mounting method, Fig B. - Load(%) is percent of maximum output load ( Item2 and not exceed derating in both Maximum Output Current and Power. -For standard mounting, refer to derating curve (CA735-01-02_) DLP180-24-1 SPECIFICATIONS MODE ...
Page 2
... CA735-01-02 (This specifications sheet also apply to option model /E,/EJ) 100 -10 DLP180-24-1 OUTPUT DERATING DLP180-24-1 *COOLING: CONVECTION COOLING LOADING CONDITION(%) Standard Mounting Ta(°C) -10~50 60 OUTPUT DERATING CURVE (°C) Output connector STANDARD MOUNTING DENSEI-LAMBDA 100 Rail Input connector ...