MINI-PS-100-240AC/24DC/1 Phoenix Contact, MINI-PS-100-240AC/24DC/1 Datasheet - Page 6

no-image

MINI-PS-100-240AC/24DC/1

Manufacturer Part Number
MINI-PS-100-240AC/24DC/1
Description
POWER SUPPLY PRIMARY SWITCH MODE
Manufacturer
Phoenix Contact
Datasheet

Specifications of MINI-PS-100-240AC/24DC/1

Power Supply Type
Switch Mode
Power Supply Output Type
Fixed
No. Of Output Channels
1
Input Frequency
65Hz
Output Voltage
24VDC
Output Current
1A
Input Voltage
85V To 265V
Supply Voltage
RoHS Compliant
No. Of Outputs
1
Supply Voltage Typ
110V AC /
Rohs Compliant
Yes
Power Supply, Primary Switch Mode, Narrow Design – MINI-PS-100-240AC/24DC/1
Connection Cable:
connectors. This reliable user-friendly connection
method enables quick device connection and safe
isolation of the electrical connection, if required.
Only operate connectors when the power is
switched off.
The following cable cross sections can be connected:
For reliable and safe-to-touch
connection: Strip 7 mm (0.28 in.)
from the connector ends.
connections L and N. The device can be connected to
single-phase AC networks or to two external
conductors for three-phase networks (TN, TT or IT
network according to VDE 0100 T300/IEC364-3) with
nominal voltages of 100 - 240 V AC.
Protecting the Primary Side
specifications of EN 60 950. It must be possible to
switch off the device using a suitable disconnecting
device outside the power supply.
provided for two-phase operation using two external
conductors for a three-phase network.
used.
internal fuse is present.
Recommended Fuse:
Circuit breaker 6 A or 10 A, Characteristic B
1 1 1 1
2 2 2 2
3 3 3 3
6.2. Connection of Various Types of Network: 100 - 240 V AC Networks
6.3. Input (
The device is equipped with COMBICON
The 100 - 240 V AC connection is made using screw
The device must be installed according to the
Note that an all-pole disconnecting device must be
Additional device protection is not required, as an
For example, primary side line protection could be
TN-S network
Input:
Output:
Signal:
L N
L N
MINI
MINI
1 1 1 1
, Figure 9)
+
0.2 - 2.5
0.2 - 2.5
0.2 - 2.5
+ –
[mm
Solid
2
]
L1
L2
L3
N
PE
L
N
PE
0.2 - 2.5
0.2 - 2.5
0.2 - 2.5
Flexible
[mm
2
]
TN-C network
L N
25 - 14 0.5 - 0.6 4.4 - 5.3
25 - 14 0.5 - 0.6 4.4 - 5.3
25 - 14 0.5 - 0.6 4.4 - 5.3
L N
MINI
MINI
AWG
(0.28 in.)
[Nm]
7 mm
PHOENIX CONTACT page 6 of 8
+
+ –
Torque
[Ib in.]
L1
L2
L3
PEN
L
PEN
(or equivalent).
TT network
L N
L N
MINI
MINI
If the internal fuse is blown, this is most
probably due to a device fault.
In this case, the device should be
checked in the factory.
1 1 1 1
+
+ –
L1
L2
L3
N
L
N
4 4 4 4
IT network
L
MINI
N
2 2 2 2
Figure 08
Figure 09
3 3 3 3
+
L1
L2
L3
PE

Related parts for MINI-PS-100-240AC/24DC/1