5302-01236-0 Murata Power Solutions Inc, 5302-01236-0 Datasheet - Page 4

• Manufacturer Part Number: 5302-01236-0
• Description: DMS-EB Blank PC-Board DMS-30
• Manufacturer: Murata Power Solutions Inc

Specifications of 5302-01236-0

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Example
7. Current Measurements (Use 200mV Model, DMS-30-0): The follow-
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: [phone] [phone] Fax: [phone]
www.murata-ps.com email: [e-mail] ISO 9001 and 14001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
ing instructions are for measuring current derived from the DMS-
30/40's power source. When measuring current that is floating with
respect to J1, pin 6 (POWER RETURN), leave SG5 closed.
CAUTION: Do not exceed 1 Ampere input current
V
IN
1. Assume R1 = 1.0MΩ.
2. R2 = (FSI x R1) / ( |V
3. Calibrate the meter using a known voltage source. Adjust R4 to
is 0-5Vdc, and the display reading must be "000" to "1500."
R2 = (1.500 x 1,000,000) / (5.0 - 1.500)
R2 = 428,571Ω or 432kΩ
compensate for variations in R1 and R2.
IN
| - FSI)
www.murata-ps.com
© 2008 Murata Power Solutions, Inc.
Multi-Purpose Application Board for DMS-30 & DMS-40 Series Meters
12/15/08
Figure 4. DMS-EB Board
APPLICATIONS
USA:
Canada:
UK:
France:
Germany:
Japan:
China:
Singapore:
HI
(+) (–)
LO TST TST +V
Example
7.1. Install R2: R2 = FSR / (I
7.2. Open SG5.
7.3. Configure the DMS-EB for span adjust using the procedure previ-
7.4. Apply input signal (current) to (+) IN HI and (–) IN LO.
7.5. Adjust R4 for desired full scale readings.
7.6. Enable the appropriate decimal point using either SG1, SG2, SG3
A 0.100 Ampere input must read "100.0" on the display.
IN OUT
Mansfield (MA), Tel: [phone], email: [e-mail]
Toronto, Tel: [phone], email: [e-mail]
Milton Keynes, Tel: [phone], email: [e-mail]
Montigny Le Bretonneux, Tel: [phone], email: [e-mail]
München, Tel: [phone], email: [e-mail]
Tokyo, Tel: [phone], email: [e-mail]
Osaka, Tel: [phone], email: [e-mail]
Shanghai, Tel: [phone], email: [e-mail]
Guangzhou, Tel: [phone], email: [e-mail]
Parkway Centre, Tel: [phone], email: [e-mail]
meter reading (0 -1999) and I
ously outlined for the DMS-30-0 version.
or SG-17.
R2 = 1000 / (0.1 x 10000)
R2 = 1 Ohm
Enable DP3 via SG3 for a reading of "100.0."
–V
GND
Technical enquiries email: [e-mail], tel:
MAX
. x 10000) where FSR is the desired
MAX
is between 0 -1 Ampere.
MPM_DMS-EB.B01 Page 4 of 4
DMS-EB
[phone]