AM-500MC Murata Power Solutions Inc, AM-500MC Datasheet - Page 2

• Manufacturer Part Number: AM-500MC
• Description: Amplifer
• Manufacturer: Murata Power Solutions Inc

FUNCTIONAL SPECIFICATIONS
(Typical at +25°C, ±15V dc supply, unless otherwise noted.)
DATEL
Footnotes:
➀ dc only
➁ - 3 dB Single-pole bandwidth
➂ 1k Input and feedback resistors, 2.4 pF feedback capacitor
INPUT CHARACTERISTICS
Common Mode Voltage Range ➀
Maximum Input Voltage, no damage
Differential Input Impedance
Input Bias Current
Input Offset Current
Input Offset Voltage
OUTPUT CHARACTERISTICS
Output Voltage
Output Current, S.C. protected
Stable Capacitative Load
Output Impedance
DC Open Loop Gain
Input Offset Voltage Drift
Input Bias Current Drift
Input Voltage Noise ➁
Input Current Noise ➃
Power Supply Rejection Ratio
DYNAMIC CHARACTERISTICS
Gain Bandwidth Product
Slew Rate, positive going
Slew Rate, negative going
Full Power Frequency
Settling Time
Overload Recovery Time
POWER REQUIREMENTS
Voltage, rated performance
Voltage, operating
Quiescent Current
PERFORMANCE
0°C to + 70°C
-55°C to +125°C
0°C to + 70°C
-55°C to +125°C
0.01 Hz to 1 Hz
100 Hz to 10 kHz
1 Hz to 10 MHz
100Hz to 10kHz
10Hz to 1MHz
(20V peak-to-peak)
10V step to 1%
10VsteptoO.1%
10VsteptoO.01%
0.01Hz to 10Hz
®
3
3
3
MIN.
± 10
±10
±25
100
80
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3
doubles every 10°C
TYP.
®
1000
1800
±18
±50
100
130
100
±15
10
-20
0.5
0.5
1.6
5.2
±5
30
25
15
20
16
70
10
22
—
—
—
—
1
1
5
5
1
6
• 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 USA • Tel: [phone] • www.datel.com • e-mail: [e-mail]
MAX.
± 18
100
200
10
25
33
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4
8
3
5
5
UNITS
μVrms
μVrms
μVrms
μVrms
pA/°C
μVp-p
μVp-p
μV/°C
μV/°C
Volts
Volts
Volts
Meg
MHz
V/μs
V/μs
MHz
Vdc
Vdc
mV
mA
V/V
mA
nA
nA
dB
pF
ns
ns
ns
μs
Ω
TECHNICAL NOTES
1. The circuit design shows the connection of the AM-500
2. A small feedback capacitor should be used across the
where G is closed loop gain and Rf is in kilohms.
3. Summing point leads must be kept as short as possible.
4. Low output impedance power supplies should be used with
5. Although these amplifi ers are inverting mode only, a dc
6. For interrupted power applications, apply power to the AM-
PHYSICAL/ENVIRONMENTAL
Operating Temp. Range
Storage Temp. Range
Package Type
Pins
Weight
series for fast settling operation with a closed loop gain of
-1. It can be used for fast settling at closed loop gains up
to -10. The equivalent resistance seen by the summing
junction should be 500 ohms or less. For gains larger than
- 1 use an input resistor of 500 ohms and pick a feedback
resistor for the required closed loop gain (1k for -2, 1.5k for
-3, etc.).
feedback resistor. Determine C in nanofarads from the
following formula:
Input and feedback resistors should be soldered close to
the body of the resistor directly to the summing point (pin
4). Summing point capacitance to ground must be kept very
low.
1 μF tantalum bypassing capacitors at the amplifi er supply
terminals. There are internal 0.03 μF ceramic capacitors in
the amplifi er.
voltage in the range of ± 5V may be applied to the positive
input terminal for offsetting the amplifi er.
500 three (3) seconds before operating the device.
AM-500GC
AM-500MC
AM-500MM, MM-QL
Ultra-Fast Operational Amplifi ers
C =
01 Apr 2011 MDA_AM-500.B02 Page 2 of 4
0.816Rf
1 + |G|
AM-500 Series
MIN.
–55
–55
0
0
0.09 ounces (2.5 grams)
0.010xO.018˝ Kovar
TYP.
14-pin ceramic
—
—
—
—
MAX.
+125
+125
+70
+70
UNITS
°C
°C
°C
°C