PH300S48-24 TDK Corporation, PH300S48-24 Datasheet - Page 47
![no-image](/images/manufacturer_photos/0/6/653/tdk_corporation_sml.jpg)
PH300S48-24
Manufacturer Part Number
PH300S48-24
Description
Power Supply, Power Rating 300 Watt, Output Current Rating 12.50 Ampere
Manufacturer
TDK Corporation
Datasheet
1.PH300S48-24.pdf
(58 pages)
Specifications of PH300S48-24
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PH300S48-24
Manufacturer:
LAMBDA
Quantity:
37
Company:
Part Number:
PH300S48-24
Manufacturer:
LAMBDA
Quantity:
134
Part Number:
PH300S48-24
Quantity:
60
・All specifications are subject to change without notice.
PH
C2, C3: 4700pF
Use a ceramic capacitor that has high withstand voltage to
reduce the output spike voltage.
Select the capacitor from the above recommended compo-
nents with high withstand voltage because the test voltage
is applied to the capacitor during the withstand voltage
test in some application contents.
Connect C2 between +Vin and baseplate and C3 between
-Vin and baseplate as short as possible.
C4: 2.2μF
Also, use a ceramic capacitor to reduce the output noise
voltage.
Attach the ceramic capacitor between +V and -V where
less than 50mm from output terminal for PH300S.
For PH600S, attach the ceramic capacitor between +V
and -V terminal as short as possible.
The output spike noise voltage could be changed for de-
sign of printed circuit board.
C5:
Use electrolytic capacitor(s) for stable operation.
Attach the electrolytic capacitor between +V and -V where
less than 50mm from output terminal for PH300S.
For PH600S, attach the electrolytic capacitor between +V
and -V terminals as short as possible. Recommend tighten
the screws of load wire and C5 together.
Oscillation waveform could be shown at dropping down the
output for characteristics of equivalent series resistance
(ESR) of electrolytic capacitor and equivalent series induc-
tance (ESL).
Moreover, note the output ripple voltage could be changed
for design of printed circuit board.
In case input/output dynamically changes, it helps the fluc-
tuation of output voltage by increasing the external capaci-
tor value.
*1 For 48V output model, use two 50V capacitors in series that
Vo
Table1-2 C5: Recommended Values of External Output
have low impedance.
3.3V
12V
15V
24V
28V
48V
300S, 600S
5V
48VDC Input : 1.5kVAC or above
280VDC Input : 3kVAC or above
Wo
Capacitor
*1 470μF × 2
4700μF
3900μF
1000μF
1000μF
560μF
470μF
300S
6.3V
10V
25V
25V
35V
50V
50V
*1 680μF × 2
10000μF
4700μF
2200μF
2200μF
1000μF
820μF
600S
6.3V
10V
25V
25V
35V
50V
50V
Remarks:
1. Use an electrolytic capacitor that has excellent low imped-
2. Be aware of ripple current allowance of the electrolytic ca-
C6:
In between input source and input line of PH300S, 600S
series there are a switch and connectors etc. In case that
the switch is on/off or plug in/off when the input is apply-
ing, attach an electrolytic capacitor, C6 as shown as Fig-
ure1-3.
Because in-rush current flows when the input is applied,
confirm I
Recommended Values
If plural numbers of module will be connected in PH300S,
PH600S series, attach an electrolytic capacitor, C6 as
shown as Figure1-4.
Recommended Values
Figure1-4 Input Filter when Plural Power Modules are
ance for temperature characteristic.
(Equivalent electrolytic capacitor in LXY series manufac-
tured by Nippon Chemicon)
pacitor. Especially be aware it when the load current is in
dynamics.
The output voltage may be greatly varied in 300Hz - 2kHz
frequency range at 0%←→100% of dynamic load condition.
For less dynamic of the voltage, use a electrolytic capacitor
which has better capacity than recommended electrolytic
capacitor or keep the minimum load current more than 10%
of nominal current.
Contact us for the details.
280VDC Input : 10 - 47μF
280VDC Input : 10 - 47μF
48VDC Input : 100 - 470μF
48VDC Input : 100 - 470μF
Switch
2
+
t for the switch and fuse.
Figure1-3 Input Filter with Input Switch
+
C6
connected.
C6
Fuse
Fuse
Fuse
+
+
+
C1
C1
C1
L1
L1
L1
C2
C2
C2
C3
C3
C3
+Vin
−Vin
+Vin
−Vin
+Vin
−Vin
Baseplate
Baseplate
Baseplate
B-345
PH