SHM-4860MC Murata Power Solutions Inc, SHM-4860MC Datasheet - Page 3

• Manufacturer Part Number: SHM-4860MC
• Description: Sample-and-Hold
• Manufacturer: Murata Power Solutions Inc

Functional Specifications
(Typical at +25°C with ±15V and +5V supplies unless otherwise noted.)
Input/Output Voltage Range
Input Impedance
Output Current
Output Impedance
Maximum Capacitive Load
Input Logic Level
Logic "1"
Logic "0"
Loading
Logic "1"
Logic "0"
Gain
Gain Accuracy
Gain Linearity Error
Sample-Mode Offset Voltage
Sample-to-Hold Offset Error
(Pedestal)
Gain Tempco (Drift)
Sample-Mode Offset Drift
Sample-to-Hold Offset Drift
Acquisition Time
Sample-to-Hold Settling Time
Sample-to-Hold Transient
10V to ±0.01%FS
10V to ±0.1%FS
10V to ±1%FS
1V to ±1%FS
10V to ±0.01%FS
10V to ±0.1%FS
I±15V Supply Voltages, Pins 24, 22
+5V Supply Voltage, Pin 9
Analog Input, Pin 13
Digital Inputs, Pins 11, 12
Output Current
TRANSFER CHARACTERISTICS
DYNAMIC CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
ANALOG INPUT/OUTPUT
DIGITAL INPUT
MIN.
±10.25
—
—
—
+2.0
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
±18V
–0.5V to +7V
±18V
–0.5V to +7V
±65mA
TYP.
±11.25
1
—
0.1
250
—
—
—
—
–1
±0.05
±0.005
±0.5
±2.5
±0.5
±3
±4
160
100
90
75
60
40
180
www.murata-ps.com
MAX.
—
—
±40
—
—
+5.0
+0.8
+40
–1.6
—
±0.1
±0.01
±5
±20
±5
±15
—
200
170
—
—
100
—
—
UNITS
V
kΩ
mA
kΩ
pF
V
V
μA
mA
V/V
%
%FS
mV
mV
ppm/°C
ns
ns
ns
ns
ns
ns
mV p-p
Industry-Standard, High-Speed ±0.01% Sample-Hold Amplifiers
Aperture Delay Time
Aperture Uncertainty (Jitter)
Output Slew Rate
Output Slew Rate
Small Signal Bandwidth (–3dB)
Droop: +25°C
Feedthrough Attenuation
Overload Recovery Time
Voltage Range: ±15V Supplies
Power Supply Rejection Ratio
Quiescent Current Drain
Power Consumption
Operating Temperature Ranges
Storage Temperature Range
Package Type
Output
Footnotes:
tained short to ground. However, shorts from the output to either supply will cause permanent damage.
For normal operation, the load current should not exceed ±40mA.
TECHNICAL NOTES
1. All ground pins (10, 15, 21, 23) should be tied together and connected to system analog ground
as close to the package as possible. It is recommended to use a ground plane under the device and
solder all four ground pins directly to it. Care must be taken to ensure that no ground potentials
can exist between Pin 10 and the other ground pins.
2. Although the power supply pins (9, 22, 24) are internally bypassed to ground with 0.01μF ceramic
capacitors, additional external 0.1μF to 1μF tantalum bypass capacitors may be required in critical
applications.
3. A logic "0" on the HOLD COMMAND input (Pin 11), or a logic "1" on the HOLD COMMAND input
(Pin 12), will put the device in the sample mode. In this mode, the device acts as an inverting unity-gain
amplifier, and its output will track its input. A logic "1" on Pin 11 (logic "0" on Pin 12) will put the device
in the hold mode, and the output will be held constant at the last input level present when the hold
command was given. If the HOLD COMMAND input (Pin 11) is used to control the device, Pin 12 must
be tied to digital ground. If HOLD COMMAND input (Pin 12) is used to control the device, Pin
11 must be tied to +5V.
4. The maximum capacitive load to avoid oscillation is typically 250pF. Recommended resistive load is
500Ω, although values as low as 250Ω may be used. Acquisition and sample-to-hold settling times are
relatively unaffected by resistive loads down to 250Ω and capacitive loads up to 50pF. However, higher
capacitances will affect both acquisition and settling time.
Positive
Negative
SHM-4860MC
SHM-4860MM, 883
Input signal should not exceed the supply voltage.
The SHM-4860’s output is current limited at approximately ±65mA. The device can withstand a sus-
Full Scale (FS) = 10V. Full Scale Range (FSR) = 20V.
Sample-to-Hold Offset Error (Pedestal) is constant regardless of input/output level.
Units are ppm of FSR/°C.
+70°C
+125°C
+5V Supply
+15V Supply
–15V Supply
+5V Supply
DYNAMIC CHARACTERISTICS , Continued
Technical enquiries email: [e-mail], tel:
PHYSICAL/ENVIRONMENTAL
POWER REQUIREMENTS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0 to +70°C (ambient)
–55 to +125°C (case)
–65 to +150°C
24-pin ceramic DDIP
6
±50
±300
±300
16
±0.5
±15
±1.2
74
200
700
±3
±5
±0.5
+21
–22
+17
730
MDA_SHM-4860.B01 Page 3 of 4
SHM-4860
—
—
—
—
—
±5
—
—
—
—
—
—
—
—
+25
–25
+25
875
[phone]
ns
ps
μV/μs
μV/μs
MHz
μV/μs
μV/μs
mV/μs
dB
ns
ns
%
%
mV/V
mA
mA
mA
mW