SMT15E-12W3V3-TJ Emerson Network Power, SMT15E-12W3V3-TJ Datasheet - Page 27

• Manufacturer Part Number: SMT15E-12W3V3-TJ
• Description: 10-14Vin, 0.8-3.63V@15A, 1.30" X 0.53" X 0.32, 94%Eff, SMT, T&R Packaging, RoHS 6
• Manufacturer: Emerson Network Power

Specifications of SMT15E-12W3V3-TJ

• Product: Non-Isolated / POL
• Output Power: 55 W
• Input Voltage Range: 10 V to 14 V
• Input Voltage (nominal): 12 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.8 V to 3.63 V
• Output Current (channel 1): 15 A
• Package / Case Size: 33.02 mm x 13.46 mm x 8.13 mm
• Output Voltage: 0.8 V to 3.63 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Special Features
Bulk Power (HPS)
350-3000 Watts
HPS
Environmental Specifications
Safety
• EN61000-3-2 harmonic
• Built-in EMI filter
• Low output ripple
• +5 V standby output
• Built-in cooling fans
• Overcurrent protection
• Overvoltage protection
• Over temperature protection
• Hot swap/N + 1 redundant
• Built-in OR’ing diodes
• Active power factor correction
Voltage Availability
Available Standard Output Voltages (order code)
Notes:
HPS15 and HPS35
Operating
temperature
HPS3KW
Operating
temperature
Cooling
UL
NEMKO
TUV
CE
CB
Corresponding Rack
Available Options
Refer to data sheet
Power/Series
35 - 350 W
15 - 1500 W
3K - 3000 W
compliance
Voltage Code
Input Voltage
1 = Consult factory for other output voltages and options
2 = Comes with I
3 = 1200 W@ 90-264 Vac; 1500 W@100-264 Vac
(L - Y)
12 (L)
24 (Q)
28 (R)
30 (S)
48 (W)
54 (X)
60 (Y)
Wattage
Model
-
UL60950 (UL recognized)
EN60950
EN60950
Mark
Report
Imonitor
(HPS 15 only)
N = none
A = current monitor
Redundancy
always R
90-264 Vac
See Note 1
HPR1-00
R
-10 °C to 50 °C ambient (derate output
@ 2.5% per degree from 50 °C to 70 °C)
5 °C to 40 °C
Internal DC fans
HPS35
350 W
2
C interface
•
•
•
•
-
Aux Fan voltage
(HPS15 only)
N = none
3 = 12 V @ 4 A
5 = 24 @ 2 A
90-264 Vac
See Note 1
1500 W
HPR3-00
New Features
Coming Soon
• HPR1 split Rack
• 500 W HPS50
HPS15
Standard Option*
Codes (000 - 256)
For complete product specifications, technical reference notes and available product options, go to www.powerconversion.com.
•
•
•
•
•
•
(dual output voltage)
1
3
180-264 Vac
HPR3KW-00
See Note 2
HPS3KW
3000 W
•
•
Electrical Specifications
*3 A minimum for current share operation
Input HPS35
Input voltage
Frequency
Inrush current
Efficiency
Power factor
Turn-on time
EMI filter standard
Leakage current
standard
Radiated EMI
Holdover time
AC OK
Harmonic distortion Meets EN61000-3-2
Isolation
Output HPS35
Adjustability
Overall req
Ripple
Dynamic response
Recovery time
Over current
protection
short-circuit
protection
Overvoltage
protection
Reverse voltage
protection
Thermal protection
Remote sense
Single wire parallel
DC OK
Minimum load*
Standby voltage
Global inhibit
90-264 Vac typical
47-440 Hz
40 A peak max.@ 25 °C
80% typical @ full load, 230 Vac
0.99 typical @ 115 Vac, full load
AC on 2 sec; inhibit/enable 160ms typical
CISPR 22; EN55022 Level “B”
<0.5mA max @ 230 Vac @ 60 Hz per module
CISPR 22; EN55022 Level “B”
20ms minimum (independent of input Vac)
5ms early warning minutes before outputs
lose regulation
Meets EN60950
±5% of nominal output voltage
±2%
1% of Vout Pk-Pk (20M Hz bandwidth)
4% with 25% load step
To within 1% in <300 μsec
115%-130% of rated output current
Protected for continuous short-circuit
Auto recovery
120-140%. AC Reset
100% of rated output current
Main and Aux disabled when internal
temperature exceeds safe operating range
Up to 0.5 V total drop
Current share to within 10% of total
rated current on main output
±5% of nominal
Not required (when used as stand-alone module)
5 Vdc @2 A maximum present
whenever AC input is applied
Logic “0”
HPR1
Bulk Power
27